background image

Page 2

MD38-BV  Homefire

Introduction

About the M38 Series Modular Fireplaces:

The 

MD38-BV 

includes a 28,000 BTU dual burner and embers. All 38

Series Modular Fireplaces allow quick and easy upgrades in the future.
The MD38-BV can be upgraded to a Wildfire Burner. Contact your
dealer for more information. The MD38-BV model is available in two
versions:

n

Continuous Pilot - (Product Code MD38

B

)

n

Intermittent Pilot - (Product Code MD38

B-I

)

The MD38-BV is rated for Natural Gas at 28,000 BTU/H 8.5 Kilowatts)
Input or

 

Propane at 28,000 BTU/H (8.5 Kilowatts) Input.

How to use this manual:

This manual covers all models and unless otherwise specified, the
designation MD38-BV refers to all models. Sections which are specific
to a particular model are marked with a     symbol, plus the appropriate
model number.

Warranty and Installation Information:

The Montigo warranty will be voided by, and Montigo

 

disclaims any

responsibility for, the following actions:

n

Modification of the fireplace and/or components including Direct-
Vent assembly or glass doors.

n

Use of any component part not manufactured or approved by
Montigo in combination with this Montigo fireplace system.

n

Installation other than as instructed in this manual.

Consult your local Gas Inspection Branch on installation requirements
for factory-built gas fireplaces. Installation & repairs should be done by
a qualified contractor.

Installations in Canada

 must conform to the current 

CAN/CGA B-

149.1

 and 

.2

 Gas Installation Code and local regulations. If the optional

air-circulating fan kit is installed, it must be electrically grounded in
accordance with 

CSA C22.1

 Canadian Electrical Code Part 1 and/or

Local Codes.

Installations in the USA

 must conform to local codes, or in the

absense of local codes to the National Fuel Gas Code, 

ANSI Z223.1-

1988

. If the optional air-circulating fan is installed, it must be grounded

in accordance with local codes or, in the absence of local codes, with
the National Electrical Code, 

ANSI/NFPA 70-1987.

Table Of Contents

Introduction .............................................................................

2

Installation

Installing the Fireplace Shell ......................................... 3

Installing the Gasline ..................................................... 4

The Remote Switch ....................................................... 4

B-Vent Installation ......................................................... 4

Construction around the fireplace

Facing ............................................................... 5

Mantels and Surrounds ..................................... 5

Wiring ...................................................................... 5-6

Installing the Logset ...................................................... 6

Removing and Installing the Insert ................................ 7

Removing and Installing the Door ................................. 7

Operation ..........................................................................

8 - 10

Maintenance ...................................................................

10 - 11

Warranty .................................................................................

12

Appendix

A. Accessories ............................................................ 13

CAUTIONS

Due  to  its  high  operating  temperatures,  the  appliance
should  be located out of traffic & away from furniture and
draperies.

n

Children and adults should be alerted to the hazards
of the high surface temperature, which could cause
burns or clothing ignition.

n

Young children should be carefully supervised when
they are in the same room as the appliance.

n

Clothing or other flammable materials should not be
placed on or near the appliance.

Summary of Contents for MD38-BV















Reviews: