background image

®

C

US

XG0677

141231

 

Proflame 2 

System   

 

Operation & Maintenance Manual

Read these instructions before use. 

NOTICE

FIRE HAZARD. Can cause severe injury or death.

 The Transmitter and IFC 

  

 

.

WARNING

 device causes ignition of the appliance. The appliance can turn on suddenly. 

 Keep away from the appliance burner when operating the remote system or 

 activating manual bypass of the remote system.  

  

  

Property Damage Hazard. Excessive heat can cause property damage. 

The appliance can stay lit for many hours. Turn off the appliance if it is not going

 be attended for any length of time. 

  

 

.

CAUTION

- Turn OFF the main gas supply of the appliance during installation or 

  maintenance of the receiver device.

- Turn OFF main gas supply to the appliance prior to removing ro reinserting the 

   batteries.

- In case of remote control malfunction turn OFF the IFC device using the On/Off 

  main switch.

- For installation / maintenance switch OFF the IFC device by removing main 

power supply plug and disconnect. 

ATTENTION

Do not operate in presence of water dripping, spraying, rain, etc. 

WARNING

 

Canadian Heating Products Inc. 

Langley, BC  V4W 4A1   |   

Montigo Del Ray Corp.

 Ferndale, WA  98248

 

 

 

WARNING

When installing the fireplace - gas lines, fittings, 

accessories or any other objects cannot impede the 

proper movement of the door buckles.

Summary of Contents for Proflame 2











Reviews: