Montigo R520-ST Installation & Maintenance Manual Download

Page: 13 / 36

Section 4-1-3: Installation of the Vertical External

Roof Mounted Power Vent Module

Refer to

AppendixA-PowerVentlocations

, to ensure the planned

Vertical Power vent location is acceptable.

See

PowerVentmanual

for installation instructions.

Section 4-1-2: Venting Components

The following venting components and associated Montigo part

numbers are available for the appliance:

Connection and installation of the vent components should

adheretothefollowingguidelines:

■ Connect all vent sections using a minimum of three sheet

metal screws on the outer pipe flue.

■ Ensure the pipe ends male to female slide in a minimum

of 1 1/2“ of overlap.

■ Ensure all horizontal runs are supported with a minimum

of 3 supports per 10’ of venting.

■ When hanging/ supporting venting, ensure that 1” clearance

is maintained on all sides to any combustible material.

■ Ensure when cutting sections of rigid pipe to maintain

integrity of internal supports.

■ Place the springs, supplied with the pipe kit, between the

outer and inner pipes to keep the pipes separate and avoid

any possible hot spots.

■ Montigo recommends the use of a flex section for the final

pipe connected directly to the fireplace offering greater

flexibility of installation and absorption of movement.

■ All exterior joints in venting should be sealed with high heat

silicone RV230.

A - Termination

PVVEX510-300

B - Rough-in Frame

Supplied with PVVEX510-300

C - Flex Sections

RLF-1 (12" Section)

RLF-2 (24" Section)

RFL-3 (36" Section)

RFL 4 (48" Section)

D - Rigid Sections

REXT-1 (12" m/f Section)

RXT-20 (20" Section)

REXT-2 (24" m/f Section)

REXT-3 (36" m/f Section)

REXT-4 (48" m/f Section)

E - Elbows

REL-90MM (m/m 90

Elbow

REL-90FF (f/f 90

Elbow

REL-90FM (f/m 90

Elbow)

REL-45FM (f/m 90

Elbow)

F - Power Cord

Harnesses

EPVH10-10 foot power cord & harness

EPVH20-20 foot power cord & harness

EPVH30-30 foot power cord & harness

EPVH40-40 foot power cord & harness

EPVH50-50 foot power cord & harness

EPVH60-60 foot power cord & harness

EPVH70-70 foot power cord & harness

EPVH80-80 foot power cord & harness

EPVH70-70 foot power cord & harness

EPVH80-80 foot power cord & harness

EPVH90-90 foot power cord & harness

EPVH100-100 foot power cord & harness

R520-ST & R620-ST Power Vent Indoor Gas Fireplace

Page 13

XG0773 - 150127

Installation

Summary of Contents for R520-ST





































Search results

Summary of Contents for R520-ST

Reviews:

Related manuals for R520-ST

Brands by name

Popular brands

Montigo R520-ST, Installation & Maintenance Manual

Search results

Summary of Contents for R520-ST

Reviews:

Related manuals for R520-ST

Brands by name

Popular brands