background image

Page 2

Part No. XG0512

Rio DX Cast Stove

Introduction

About this Stove:

Thank you for purchasing the 

Rio DX Cast Stove, 

and choosing a 

Delray Gas Product. This Rio Stove

 

features a 28,000 BTU double 

burner with embers, and a hi-lo adjustable control. .
This Stove is certified for use with Montigo Direct Vent Components. 
The Rio DX Stove is certified as a heating appliance by CGA and 
AGA tothe 

Vented Gas Fireplace Heater

 standard (ANSI Z21.88-

2005 · CGA 2.33-2005) and is rated for:
 

Natural Gas

   28,000 BTU/H Maximum Input

 

 

 

20,500 BTU/H Minimum Input

 

Propane

 

28,000 BTU/H Maximum Input

 

 

 

20,500 BTU/H Minimum Input

How to use this manual:

This manual covers installation, operation and maintenance. Light-
ing, operation and care of this fireplace can be easily performed by 
the homeowner. However, all installation and service work should be 
performed by a qualified or licensed installer, plumber, or gasfitter 
who is qualified or licensed by the state, province, region, or govern-
ing body in which the appliance is being installed.
This manual covers all versions. Sections which are specific to a 
particular version are marked with a symbol, plus the appropriate 
model number.

Warranty and Installation Information:

The Montigo warranty will be voided by, and Montigo

 

disclaims any 

responsibility for, the following actions:

 

Modification of the fireplace and/or components including Direct-
Vent assembly or glass doors.

 

Use of any component part not manufactured or approved by 
Montigo in combination with this Montigo fireplace system.

 

Installation other than as instructed in this manual.

Consult your local Gas Inspection Branch on installation require-
ments for factory-built gas fireplaces. Installation & repairs should be 
done by a qualified contractor.

Installations in Canada

 must conform to the current 

CAN/CGA 

B-149.1

 and 

.2

 Gas Installation Code and local regulations. If the 

optional air-circulating fan kit is installed, it must be electrically 
grounded in accordance with 

CSA C22.1

 Canadian Electrical Code 

Part 1 and/or Local Codes.

Installations in the USA

 must conform to local codes, or in the 

absense of local codes to the National Fuel Gas Code, 

ANSI 

Z223.1-1988

. If the optional air-circulating fan is installed, it must be 

grounded in accordance with local codes or, in the absence of local 
codes, with the National Electrical Code, 

ANSI/NFPA 70-1987. 

See 

Appendix A for fireplace installations within the State of Mas

-

sachusetts

.

Table Of Contents

Introduction

 ............................................................................... 2

Installation

 

Choosing a Location ...................................................... 3

 

Installing the Gasline ...................................................... 4

 

Direct Vent Installation ................................................... 4

 

 

General Requirements ...................................... 4

 

 

Terminations ...................................................... 4

 

 

Horizontal

(Top Vent Through-the-Wall)

 Installations 6

 

 

Vertical 

(Top Vent Through-the-Roof)

 Installations . 7

 

Removing and Installing the Door .................................. 8

 

Installing the Logset ....................................................... 9

 

Wiring   ........................................................................... 9

Operation

 ..........................................................................10 - 12

Maintenance

 .....................................................................12 - 13

Warranty

 .................................................................................. 14

Appendix

 

A. Termination Locations .............................................. 15

 

B. Accessories and Vent Components ..................16 - 17

CAUTIONS

Due  to  its  high  operating  temperatures,  the  appliance 
should  be located out of traffic & away from furniture and 
draperies.

  Children and adults should be alerted to the hazards 

of the high surface temperature, which could cause 
burns or clothing ignition.

  Young children should be carefully supervised when 

they are in the same room as the appliance.

  Clothing or other flammable materials should not be 

placed on or near the appliance.

Summary of Contents for Rio DX





















Reviews: