background image

IMPORTANT SAFEGUARDS

SAFETY PRECAUTIONS

UNPACKING

SERVICE

1     Read these instructions.
2    Keep these instructions. 
3    Heed all warnings 
4    Follow all instructions.
5    Do not use this apparatus near water.
6    Clean only with damp cloth.
7    Do not block any of the ventilation openings.  Install in accordance with the  

  manufacturers instructions.

8    Cable Runs- All cable runs must be within permissible distance.
9    Mounting - This unit must be properly and securely mounted to a supporting  

  structure capable of sustaining the weight of the unit.

Accordingly:

a.  The installation should be made by a qualified installer.
b.  The installation should be in compliance with local codes.
c.  Care should be exercised to select suitable hardware to install the unit, taking into 

account both the composition of the mounting surface and the weight of the 
unit. 

10   Do not install near any heat sources such as radiators, heat registers, stoves, or other  

  apparatus ( including amplifiers) that produce heat.

11   Do not defeat the safety purpose of the polarized or grounding-type plug.  A  

  polarized plug has two blades with one wider than the other.  A grounding type  
  plug has two blades and a third grounding prong.  The wide blade or the third  
  prong are provided for your safety.  When the provided plug does not fit into your  
  outlet, consult an electrician for replacement of the obsolete outlet.

12   Protect the power cord from being walked on or pinched particularly  at plugs,  

  convenience receptacles, and the point where they exit from the apparatus.

13   Only use attachment/ accessories specified by the manufacturer.
14   Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,  

  or sold with the apparatus.  When a cart is used, use caution when moving the cart/           
  apparatus combination to avoid injury from tip-over.

15   Unplug this apparatus during lighting storms or when unused for long periods of time.
16   Refer all servicing to qualified service personnel.  Servicing is required when the  

  apparatus has been damaged in any way, such as power-supply cord or plug is  
  damaged, liquid has been spilled of objects have fallen into the apparatus, the  
  apparatus has been exposed to rain or moisture, does not operate normally, or  
  has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the 
integrity of the installation is intact. Failure to comply with the foregoing could result in the 
unit separating from the support structure and falling, with resultant damages or injury to 
anyone or anything struck by the falling unit.

Unpack carefully. Electronic components can be 

damaged if improperly handled or dropped. If an item 

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:
1  The shipping carton and packaging material.

They are the safest material in which to make 

future shipments of the equipment.

2  These Installation and Operating Instructions.

If technical support or service is needed, contact us 

at the following number:

The lightning flash with an arrowhead 

symbol, within an equilateral triangle, is 

intended to alert the user to the presence 

of non-insulated “dangerous voltage” 

within the product’s enclosure that may be 

of sufficient magnitude to constitute a risk 

to persons.

Este símbolo se piensa para alertar al usuario a la 

presencia del “voltaje peligroso no-aisIado” dentro del 

recinto de los productos que puede ser un riesgo de 

choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la 

presence “de la tension dangereuse” non-isolée dans la 

clôture de produits qui peut être un risque de choc 

électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der 

nicht-lsolier “Gefährdungsspannung” innerhalb der 

Produkteinschließung alarmieren die eine Gefahr des 

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença 

“di tensão perigosa non-isolada” dentro do cerco dos 

produtos que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla 

presenza “di tensione pericolosa” non-isolata all’interno 

della recinzione dei prodotti che può essere un rischio di 

scossa elettrica.

The exclamation point within an equilateral 

triangle is intended to alert the user to 

presence of important operating and 

maintenance (servicing) instructions in the 

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para 

alertar al usuario a la presencia de instrucciones 

importantes en la literatura que acompaña la 

aplicación.

Ce symbole de point d’exclamation est prévu pour 

alerter l’utilisateur à la presence des instructions 

importantes dans la littérature accompagnant 

l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum 

Vorhandensein de wichtigen Anweisungen in der 

Literatur alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido 

alertar o usuário à presença de instruções importantes 

na literatura que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per 

avvertire l’utente alla presenza delle istruzioni importanti 

nella letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1800 554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF 

ELECTRIC SHOCK, DO NOT REMOVE 

COVER ( OR BACK).  NO USER- SERVICE-

ABLE PARTS INSIDE.  REFER SEVICING TO 

QUALIFIED SERVICE PERSONNEL.

Summary of Contents for PDDW10CN2





















Reviews: