background image

12

© 2016 Skier’s Choice, Inc.

abanDonIng sHIP

  

bURn HaZaRD

•  Swim against the current or wind if you abandon ship.  

Leaking fuel will float with the current and may ignite.

•  When clear of danger, account for all who were on board, 

and help those in need.

•  Use distress signal.
•  Keep everyone together to make rescue easier.

FLOODING, SWAMPING OR CAPSIZING

•  STAY WITH THE BOAT!  A boat will usually float even if there 

is major hull damage.  Rescuers can spot a boat much easier 

than a head bobbing in the water.

•  Signal for help.

COLLISION

• 
•  Account for everyone on board.
•  Check for injuries.
•  Inspect structural damage.
•  Reduce flooding.
•  Signal for help.
•  STAY WITH THE BOAT!

GROUNDING

Action depends on how hard the boat hits bottom and whether 

the boat remains stranded.  If it is a simple touch, you may need 

only to inspect the hull.  If you are aground, assess the situation 

before reacting.  In some cases, throwing the boat into reverse 

can cause more damage.

Basic Guidelines
•  Inspect damage to hull, propulsion and steering systems.
•  Check for leaks.  If water is coming in, stopping the flow takes 

priority over getting free.

•  Determine water depth all around the boat and type of 

bottom (sand, mud, rocks, etc.).  This will help you decide 

which way to move the boat.

•  Determine if tide, wind or current will drive the boat  harder 

aground or will help free it.

The time to think about emergencies is 

before they happen.  Plan ahead. Know what to do before 

you encounter any of these situations.  Wear a PFD (Personal 

Flotation Device) when boating.

EXPLOSION & FIRE

 

eXPlosIon/fIRe/asPHYXIaTIon HaZaRD

•  Open flame cooking appliances consume oxygen. This can 

cause asphyxiation or death.

•  Maintain open ventilation.
•  Liquid fuel may ignite, causing severe burns.
•  Use fuel appropriate for type of stove.
•  Turn off stove burner before filling.
•  Do not use stove for comfort heating.

fIRe/asPHYXIaTIon HaZaRD 

Use special care with flames or high temperatures near urethane 

foam, if used in construction of your boat.  Burning, welding, 

lights, cigarettes, space heaters and the like can ignite urethane 

foam.  Once ignited, it burns rapidly, producing extreme heat, 

releasing hazardous gases and consuming much oxygen.

eXPlosIon

•  If explosion is imminent, put on PFDs, grab distress signals 

and survival gear, and immediately abandon ship.

fIRe

•  Turn off engines, generators, stoves and blowers.
•  Extinguish smoking materials.
•  Fixed fire suppression system, if equipped, has heat 

sensors that automatically flood machinery space with 

a fire extinguishant.  Allow extinguishant to “soak” 

compartment for at least 15 minutes to cool hot metals or 

fuel before cautiously inspecting fire area.  Have portable 

fire extinguishers ready.  Do not breathe fumes or vapors 

caused by the fire or extinguishant.

•  If no fixed firefighting system is installed and fire is in engine 

compartment, discharge portable fire extinguishers through 

transmission cover which is typically under the rear seat. 

Do not open engine hatch as this feeds oxygen to the fire.

•  If you have access to fire, direct contents of extinguishers at 

base of flames, not at the top.

•  Throw burning materials overboard if possible.
•  Move anyone not needed for firefighting operations away 

from the flames.

•  Signal for help.
•  Put on PFDs (Personal Flotation Devices), grab distress signals 

and survival gear, and prepare to abandon ship.

Reprinted from “Fishing and Skiing Boats Owner’s Manual” with permission 

from the NMMA.

Section 3

Emergency Procedures

Summary of Contents for Craz









































































Reviews: