Mooney M20TN Service And Maintenance Manual Download

Page: 241 / 1169

MOONEY AVIATION COMPANY, INC.

M20TN SERVICE & MAINTENANCE MANUAL

Page

Date

2006

Rev Date

to tailcone.

4. Rudder Torque Tube Removal. The rudder torque

tube should be inspected thoroughly and replaced if

any damage is found. Remove shield from front of cab-

in floorboard that covers torque tube. Remove attach-

ing hardware from hinges and rudder pedal control

rods. Carefully remove torque tube by sliding out to-

ward right side of cabin and through cabin door.

NOTE:

Control tube wear allowables. If any portion of

the control tube exceeds .007 inch wear per wall

or .014 inch reduction in diameter, the tube must

be replaced.

FWD

R27--9

ELEVATOR HORN ADJUSTMENT

FIGURE 27--9

27--30--00 -- ELEVATOR SYSTEM

Elevator construction is essentially the same as that of

the ailerons. Both elevators attach to the stabilizer at

four hinge points. Push--pull tubes and bellcranks link

the elevators to the control yoke. Lead counterweights

static balance the elevators (Refer to Section

27--91--00 Control Surface Static Balancing). A lead

bob--weight under the instrument panel refines aircraft

handling in flight.

1. Elevator Removal and Installation.

A. Remove push--pull control tube by taking off all

attaching bolts, nuts and washer.

B. Remove bolts, nuts and washers from the four

attaching hinges.

C. Remove elevator to the rear.
D. Install elevators in reverse sequence of remov-

al. Recheck attaching hardware for security and safety.

Set elevators, RH/LH, to be level with horizontal stabi-

lizer. Adjust rod end bearings (9) (Fig 27--9) at elevator

horns.

2. Elevator Rigging and Adjustment.

R27--10

ELEVATOR TRIM ADJUSTMENT

FIGURE 27--10

NOTE:

Measure elevator travel from 0 degrees stabilizer

thrust line with travel board positioned at stabi-

lizer station 16.00 as indicated on travel board,

P/N GSE 030004--503, and with stabilizer at 0 de-

grees. (See Fig. 27--3 and Fig. 27--10 for travel

board placement.

A. Adjust rod end bearing (3), (Fig. 27--1), at con-

trol yoke (G) for control shaft (H) clearance from firewall

and control yoke and bob--weight clearance from fuse-

lage structure.

B. Level aircraft and set control column in neutral

with stabilizer parallel to center line of aircraft.

C. Adjust rod end bearings of control tube (L) (Fig.

27--5), at rear tailcone bulkhead out approx. 5 turns to

start.

D. Adjust elevator horn rod end (9) (LH & RH), (Fig.

27--9) out 7 to 8 turns to start.

E. Main spar, adjustable rod end bearing is turned

out approx. 6 turns to start. To obtain additional elevator

travel, adjust as required.

F. Set stops (P), (Fig. 27--7), in empennage stinger

for elevator uptravel of 22

(+0/--2) and downtravel of

(+0/--2).

G. After stops (P) & (M) are set, rotate elevators

through full range of travel to assure positive contact

with stops (P) & (M), and that nuts and bolt heads clear

stop limiters (R). Stop limiters (R) may be bent to obtain
proper clearances and contact with elevator stops (P),

(Fig. 27--7).

H. Rotate stabilizer trim full down to check clear-

ance of bellcrank at wing rear spar. Adjust rod end bear-

ing at rear tailcone bulkhead (C) (Fig. 27--5), if needed,

for clearance. Recheck elevator UP and DOWN travel.

I. Rotate elevator trim FULL UP to check that UP

stop (P) makes solid contact on stop limiter (R) (Fig.

27--7).

27--30--00

Summary of Contents for M20TN


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for M20TN

Reviews:

Related manuals for M20TN

Brands by name

Popular brands

Mooney M20TN, Service And Maintenance Manual

Search results

Summary of Contents for M20TN

Reviews:

Related manuals for M20TN

Brands by name

Popular brands