ӏࡾю
MACHINING CHAMBER
72
6.
ሻȟᆍૺȪȹȗɞکնȾɂǾᆍૺኙȺȤȟɥȪȽȗɛșȾา
ȪȹȢȳȨȗǿ
6. If the window is damaged, take due care to avoid injury caused by
touching the damaged part of the glass.
7.
ɽ˂ɷʽɺȾʁʴɽʽጕ͏۶ɁɕɁɥΈႊȬɞȻʧʴɵ˂ʦʗ˂
ʒɥӐԇȨȮɑȬǿ
7. Using a material other than a silicon-based one for caulking can
degrade the polycarbonate.
ᴹਖ਼ᬲᴻ
<Procedure>
1)
ൡಽໃɥȪɖȬɞǿ
1)
Turn OFF the main power.
2)
ᚾɥɝ۶Ȭǿ
2)
Remove the window frame plate.
3)
աȗሻɥɝ۶Ȭǿ
3)
Remove the old window.
4)
ሻౕȾ͇ᅔȪȹȗɞʁʴɽʽɥɝȢǿ
4)
Remove silicon on the window frame plate.
5)
ȪȗሻɁ͇Ȥտᴥюᴬ۶ᴦɥᆬᝓɁ˨Ǿ۶ϫȾȽɞ
ᬂɁٍ֚ȾʁʴɽʽɥڴࢎȬɞǿ
5)
After confirming the mounting direction (inside/outside) of
the new window, apply silicone sealant to the edges of
outside face of the new window.
6)
Ȫȗሻɥɝ͇Ȥɞǿ
6)
Mount a new window.
2
าᜤ
2
NOTE
า୫ȾሻֿႭհȟඩȪȗȞᆬᝓȪȹȢȳȨȗǿ
Confirm that the window parts No. is correct when making an
order.
7)
ᚾɁɀȫɥ፻ɔȹሻɥِްȬɞǿ
7)
Fix the window by tightening the screws on the frame.
8)
‘
ްఙཟ೫
1’
႕ᬂȺሻ̬૰ஓɥᜫްȬɞǿ
8)
Set the replacement date on the ‘PERIODICAL
INSPECTION 1’ screen.
1
ҝёൡಽͽᝢం
“‘
ްఙཟ೫
1’
႕ᬂ
”
1
Separate volume, OPERATION MANUAL “‘PERIODICAL
INSPECTION 1’ Screen”
7-2
ൡಽюɁຏો
Cleaning Inside Machine
8
Բ᪙
8
DANGER
ൡಽໃȝɛɆࡾکϫɁൡಽႊໃᴥʠʶ˂ɵᴦɥȪɖȪ
ȹȢȳȨȗǿ
Turn OFF the main power and disconnect the plant-side
power supply (breaker).
7
า
7
CAUTION
1.
٢᎔ሳɥΈႊȪȽȗȺȢȳȨȗǿ
1.
Do not use compressed air.
ᵘҒɝȢȭᴬɹ˂ʳʽʒΞоȾɛɞൡಽ᪩ᵚ
[Machine failure due to chips and coolant entry]
2.
ӏࡾጀ࣊ɥᩋఙ፟ધȬɞȲɔǾൡಽሜӦጶ̘ȾɂຏોȪ
ȹȢȳȨȗǿ
2.
To maintain machining accuracy, clean the machining
chamber after completion of machining operations.
Window
Window Frame
Window Frame Plate
ሻ
ሻౕ
ሻɥِްȪȹȗɞᚾ
ൡሗ
ሻֿႭհ
NL1500/2000/2500
W14621
NL3000
W14622
Machine Model
Window Parts
No.
NL1500/2000/2500
W14621
NL3000
W14622
Summary of Contents for NL1500/500
