background image

The Specialist In Drum Handling Equipment

Kit # 4804-P

Wireless Remote Control Kit

Installation Instructions for Morse Wireless Remote Control Kit (Part # 4804-P) for field installation on 

 

Model 285A-BP or 285XBP Forklift-Karrier with serial number 0510 to ____ (MMYY), 289F Fork Mounted Drum 
Racker or 289C Carriage Mounted Drum Racker

morsedrum.com

Copyright 2019  -  Morse Mfg. Co., Inc. 

Form PL4804 

(0510-____) 

(Updated 11 Jun, 2019)

               

2

Safety Information

 (continued)

DANGER 

- Indicates a situation which, if not avoided, will result in serious injury or death.  

This signal word is limited to the most extreme situations.

WARNING 

- Indicates a situation which, if not avoided, could result in serious injury or 

death.

CAUTION 

- Indicates a situation which, if not avoided, can result in damage to the machine.

WARNING 

- Do Not Modify the Unit. Under no circumstances should any modifications be made to 

the Morse machinery without factory authorization.  Any modifications may void the warranty.  This 

machine was designed to perform a specific job and alterations may result in injury to operator or 

machine.

WARNING 

- No Loose Fitting Clothing. Wear close-fitting clothing and safety equipment appropriate 

to the job.  Loose fitting clothing may become caught on the machinery and cause severe personal 

injury.

CAUTION:  

DO NOT allow drum to impact on floor, ground, or dumping station, etc.

Summary of Contents for 4804-P







Reviews: