background image

The Specialist In Drum Handling Equipment

Model 83

 

 

 

 

Pail Handler

operator’s Manual for Morse Model 83

serial number 0819 to ____ (MMYY)

morsedrum.com

Copyright 2020  -  Morse Mfg. Co., Inc. 

 

Form PL83 (0819-____)   

(Updated 3 Jun, 2020)

 

             

2

safety Information

 (continued)

DAnGeR 

- Indicates a situation which, if not avoided, will result in serious injury or death.  

This signal word is limited to the most extreme situations.

WARnInG 

- Indicates a situation which, if not avoided, could result in serious injury or 

death.

CAUtIon 

- Indicates a situation which, if not avoided, can result in damage to the machine.

DANGER

 - stay Clear of Power Lines

KEEP WELL CLEAR OF POWER LINES. 

 Never approach a power line.  Current in a high voltage line may arc 

some distance from the wire to the steel framed, grounded machine.

WARNING

The 

Pail

PRO

TM

 Pail Handler is designed to handle one can or pail of the types listed at the top of page 3, under 

Machine Description

.  

DO NOT

 attempt to handle any other type of drum or object.  

DO NOT

 exceed the weight 

capacity of 150 Lb. (68 kg).

WARNING

 

- Level Floors only

For operation only on clean, level floors of suitable bearing capacity. Do not use on sloped surfaces, ramps, 

irregular or debris strewn floors.

WARNING

 - Do not Modify the Unit

Under no circumstances should any modifications be made to the Morse machinery without factory authorization.  

Any modifications may void the warranty.  This machine was designed to perform a specific job and alterations 

may result in injury to operator or machine.

WARNING

 - no Loose Fitting Clothing

Wear close-fitting clothing and safety equipment appropriate to the job.  Loose fitting clothing may become caught 

on the machinery and cause severe personal injury.

WARNING

 - stay Clear of Raised Pail

NEVER allow anyone to be below any part of a raised pail handler or pail.  Remain behind the push handle while 

handling a pail.

WARNING

 – Do NOT Disengage the clamp screw knob while pail is off the Ground

When the pail is in the upright position, lower to the floor before releasing the clamp screw knob.

CAUTION

 

– Do not transport with Can or Pail Raised

ALWAYS LOWER THE PAIL HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. 

 The unit can 

become unstable when transporting with a raised load.

CAUTION

 - Wear safety shoes

Wear safety shoes with non-slip soles and hard toe protection.

WARnInG: 

This product can expose you to chemicals including barium sulfate, cobalt, titanium dioxide, and 

2-methylimidazole, which are known to the State of California to cause cancer, and bisphenol-A, which is known to 

the State of California to cause birth defects or other reproductive harm.  

For more information go to 

www.P65Warnings.ca.gov

Summary of Contents for PailPro 83









Reviews: