background image

MAINTENANCE

M

43

REV.0-06/10

05/09/05  M43GB

NOTE

By maintenance at care of the utilizer we intend all the 

operatios  concerning  the  verification  of  mechanical 

parts, electrical parts and of the fluids subject to use or 

consumption during the normal operation of the machine.
For what concerns the fluids we must consider as main-

tenance  even  the  periodical  change  and  or  the  refills 

eventually necessary.
Maintenance operations also include machine cleaning 

operations when carried out on a periodic basis outside 

of the normal work cycle.
The repairs 

cannot be considered

 among the mainte-

nance activities, i.e. the replacement of parts subject to 

occasional damages and the replacement of electric and 

mechanic components consumed in normal use, by the 

Assistance Authorized Center as well as by manufacturer.
The replacement of tires (for machines equipped with 

trolleys) must be considered as repair since it is not de-

livered as standard equipment any lifting system.
The periodic maintenance should be performed accor-

ding to the schedule shown in the engine manual. An 

optional  hour  counter  (M)  is  available  to  simplify  the 

determination of the working hours.

ENGINE and ALTERNATOR

PLEASE  REFER  TO  THE  SPECIFIC  MANUALS 

PROVIDED.

Every  engine  and  alternator  manufacturer  has 

maintenance  intervals  and  specific  checks  for  each 

model: it is necessary to consult the specific engine or 

alternator USER AND MAINTENANCE manual.

VENTILATION

Make certain there are no obstructions (rags, leaves or 

other) in the air inlet and outlet openings on the machine, 

alternator and motor.

ELECTRICAL PANELS

Check condition of cables and connections daily.

Clean periodically using a vacuum cleaner, 

DO NOT USE 

COMPRESSED AIR.

DECALS AND LABELS

All warning and decals should be checked once a year 

and 

replaced

 if missing or unreadable.

STRENUOUS OPERATING CONDITIONS

Under  extreme  operating  conditions  (frequent  stops 

and  starts,  dusty  environment,  cold  weather,extended  

periods of no load operation, fuel with over  0.5% sulphur 

content) do maintenance more frequently.

BATTERY WITHOUT MAINTENANCE

DO NOT  OPEN THE BATTERY

The  battery  is  charged  automatically  from  the  battery 

charger circuit suppplied with the engine.

Check  the  state  of  the  battery  from  the  colour  of  the 

warning light which is in the upper part.

- Green colour: battery OK

- Black colour: battery to be recharged

- White colour: battery to be replaced

NOTE

THE ENGINE  PROTECTION NOT WORK WHEN THE 
OIL IS OF LOW QUALITY BECAUSE NOT CHARGED 
REGULARLY AT INTERVALS AS PRESCRIBED IN THE 
OWNER’S ENGINE MANUAL.

IMPORTANT

In the maintenance operations avoid that 

polluting  substances,  liquids,  exhausted 

oils, etc. bring damage to people or things or 

can cause negative effects to surroindings, 

health or safety respecting completely the 

laws  and/or  dispositions  in  force  in  the 

place.

!

!

WARNING

 

Have 

qualified

 personnel do maintenance and troubleshooting work.

 

Stop the engine before doing any work inside the machine. If for any 

reason the machine must be operated while working inside, 

pay at-

tention

 moving parts, hot parts (exhaust manifold and muffler, etc.) 

electrical parts  which may be unprotected when the machine is open.

 

Remove guards only when necessary to perform maintenance, and 
replace them when the maintenance requiring their removal is complete.

 

Use suitable tools and clothes.

 

Do not modify the components if not authorized.

  - See pag. M1.1 -

MOVING

PARTS

can injure

HOT surface

can

hurt you

!

Summary of Contents for GE 20 YSX



















































Reviews: