background image

Installation Manual  

 

 
 

7

MOTECH Industries, Inc., -  

Tainan Science Park ı No.2, Dashun 9th Rd., Xinshi Dist., Tainan City, 74145, Taiwan 

Tel: +886-6-5050789  |  E-mail

sale_marketing@motech.com.tw

                                                                           

    Page:  

 

 

 

Figure 3, the wrong connection method and the correct measurement method 

14. Maintenance 

 
 

Modules should be inspected annually for loose electrical connections, poor grounding connections, and loosened mechanical 
fastening  to  the  racking  structure.  A  module  tilt  of  at  least  10  degrees  will  help  rainfall  clean  the  modules  naturally.  Should 
cleaning of the modules become necessary, wet the glass surface before wiping with a soft sponge to prevent micro-scratches. 
Snowfall may be cleared using a soft bristle brush. If hand cleaning is not possible, pressure washer cleaning of module glass 
is permitted only when complying with all of the following restrictions: 

1.  Cleaning fluid: water at normal ambient temperature 
2.  Machine pressure rating:   13.1 MPa 
3. 

Machine flow rating:  ≤7 L/min 

4. 

Output nozzle distance to solar panel: ≥30 cm 

5. 

Spray tip water divergence: ≥ 15° 

6.  Do not clean it with chemical. 
7.  Do it in the morning or in the evening. 

 
 
 

 

 

There are no user-serviceable parts in the junction boxes.  Do not open the junction box or change intra-module 
wiring as all wiring connections are performed in the factory.  The electrical connectors cannot be used as a live 
disconnect.  Modules may only be connected and disconnected when current is not flowing (open circuit voltage 
conditions).  Always observe proper precautions when connecting or disconnecting modules exposed to light 
since hazardous voltage may be present. 

Summary of Contents for XS60GB-315








Reviews: