MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download

Page: 355 / 385

•

Remove the rubber protection cover

from the bleed valve.

•

Insert the transparent plastic pipe in

the rear brake calliper bleed valve and

insert the other end of this pipe into a

container to collect the fluid.

•

Remove the rear brake oil reservoir

cap.

•

Operate the brake lever and then open

the bleed valve on the calliper 1/4 of a

turn to let the air out.

•

Close the bleed again before reaching

the lever end of the stroke and repeat

the operation until there is no air.

•

Screw the bleeding valve and remove the pipe.

•

Top-up the reservoir until the correct brake fluid level is obtained.

•

Refit and lock the rear brake oil reservoir cap.

•

Refit the rubber protection cover.

Stelvio 1200 NTX MY11

Braking system

BRAK SYS - 355

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

Related manuals for Stelvio 1200 MY11 2011

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

Related manuals for Stelvio 1200 MY11 2011

Brands by name

Popular brands