background image

2A

2B

EN

EN

01. SAFETY INSTRUCTIONS

ATENÇÃO:

GENERAL WARNINGS

•This manual contains very important safety and usage information. 

very important. Read all instructions carefully before beginning the 

installation/usage procedures and keep this manual in a safe place 

that it can be consulted whenever necessary.

•This product is intended for use only as described in this manual. Any 

other enforcement or operation that is not mentioned is expressly 

prohibited, as it may damage the product and put people at risk 

causing serious injuries.

•This manual is intended firstly for specialized technicians, and does not 

invalidate the user’s responsibility to read the “User Norms” section in 

order to ensure the correct functioning of the product.

•The installation and repair of this product may be done by qualified 

and specialized technicians, to assure every procedure are carried 

out in accordance with applicable rules and norms.  Nonprofessional 

and inexperienced users are expressly prohibited of taking any action, 

unless explicitly requested by specialized technicians to do so.

• Installations must be frequently inspected for unbalance and the 

wear signals of the cables, springs, hinges, wheels, supports and other 

mechanical assembly parts.

• Do not use the product if it is necessary repair or adjustment is 

required.

• When performing maintenance, cleaning and replacement of parts, 

the product must be disconnected from power supply.  Also including 

any operation that requires opening the product cover.

•The use, cleaning and maintenance of this product may be carried 

out by any persons aged eight years old and over and persons whose 

physical, sensorial or mental capacities are lower, or by persons without 

any knowledge of the product, provided that these are supervision 

and instructions given by persons with experienced in terms of usage 

of the product in a safe manner and who understands the risks and 

dangers involved.

This product is certified in accordance with European 

Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the 

European Parliament and of the Council, of 8 June 2011, on 

the restriction of the use of certain hazardous substances 

in electrical and electronic equipment and with Delegated 

Directive (EU) 2015/863 from Commission.
(Applicable in countries with recycling systems).

This marking on the product or literature indicates that the 

product and electronic accessories (eg. Charger, USB cable, 

electronic material, controls, etc.) should not be disposed 

of as other household waste at the end of its useful life. To 

avoid possible harm to the environment or human health 

resulting from the uncontrolled disposal of waste, separate 

these items from other types of waste and recycle them 

responsibly to promote the sustainable reuse of material 

resources. Home users should contact the dealer where 

they purchased this product or the National Environment 

Agency for details on where and how they can take these 

items for environmentally safe recycling. Business users 

should contact their vendor and check the terms and 

conditions of the purchase agreement. This product and 

its electronic accessories should not be mixed with other 

commercial waste.
This marking indicates that the product and electronic 

accessories (eg. charger, USB cable, electronic material, 

controls, etc.) are susceptible to electric shock by direct or 

indirect contact with electricity. Be cautious when handling 

the product and observe all safety procedures in this manual.

Summary of Contents for MHACA12PMBE




















Reviews: