background image

Location

  

Package contents and location

  

For the best possible reception, we recommend that the phone is  
positioned in a central point of your home, close to where it is  
used.  
Do not place the phone behind steel doors.  
The maximum range between the telephone base and handset depends on the conditions  
around, as well as the spatial and structural factors of your home and in some  
situations range can be reduced. The indoor range is usually less  
that the externally. According to its location, the radio frequency emission can  
affect the operation and range of the phone. In these cases, the quality of  
transmission may be bad, which is characterized with an increasing incidence of  
short interruptions in the transmission. Transmission quality normal,  
turn, may be restored simply by moving a few steps  
toward the base.  
When out of range, the connection of the call will be interrupted except  
to return to a point closer to the base in ten seconds  
To avoid signal interference caused by other equipment  
electronics, we recommend that the telephone base and handset are  
located as far as possible (minimum 1 meter) of other equipment  
electronics.  
The hearing aid users should be aware that the use of mobile  
phones can interfere with the system. If this interference is too strong, can  
cause unpleasant sounds.  

AURI3500

  

AURI3500-R

  

AURI3500-MRD2

  

AURI3500-MRD3

  

 

Page 8

 

8  

Connections base

  

The  
Before you start using your phone, you must insert the plug of the cable  
telephone cord and power supply in the base.  

Telephone Cable

  

Power Supply

  

Put the plug in the socket marked with the symbol font.  
3 Route the cable from the power supply in the corresponding channel  
the base of the device.  

Connections base

  

Put the plug in the socket marked with the symbol of a  
phone.  
You must use only the power supply provided with the  
phone!  
Then insert the power supply into the wall outlet.  

Summary of Contents for AURI3500































Reviews: