Motorola DS4208 Product Reference Manual Download

Page: 36 / 364

2 - 8

DS4208 Digital Scanner Product Reference Guide

Scanning in Hand-Held Mode

Pick up the digital scanner. Press and release the trigger. The aim pattern displays.

Ensure the bar code is centered in the aiming pattern. See

Aiming

below.

Press and hold the trigger until either:

The digital scanner reads the bar code. The digital scanner beeps, the LED flashes, and the aiming pattern
turns off.

The digital scanner does not read the bar code and the aiming pattern turns off.

Release the trigger. To read another bar code, repeat steps 1, 2 and 3. Repeat this step as often as required.

Aiming

When scanning, the digital scanner projects a red LED dot which allows positioning the bar code within its field of
view. See

Decode Ranges on page 2-10

for the proper distance to achieve between the digital scanner and a bar

code.

Figure 2-5

Aiming Dot

If necessary, the digital scanner turns on its red illumination LEDs to illuminate the target bar code.

To scan a barcode, center the symbol and ensure the entire symbol is within the rectangular area formed by the
illumination LEDs.

Figure 2-6

Scanning Orientation with Aiming Dot

1D bar code

2D bar code

Summary of Contents for DS4208













































































































































































































































































































































































Search results

Summary of Contents for DS4208

Reviews:

Related manuals for DS4208

Brands by name

Popular brands

Motorola DS4208, Product Reference Manual

Search results

Summary of Contents for DS4208

Reviews:

Related manuals for DS4208

Brands by name

Popular brands