Motorola DS4800 Series Product Reference Manual Download

Page: 254 / 422

8 - 26 DS4800 Series Corded Digital Imager Product Reference Guide

OCR Check Digit Validation

Parameter # 694

Use

OCR Check Digit Validation

to protect against scanning errors by applying a check digit validation scheme.

The following is a list of options.

None

No check digit validation, indicating no check digit is applied. This is the default.

Product Add Left to Right

Each character in the scanned data is assigned a numeric value (see

OCR Check Digit Multiplier on page

8-25

). Each digit representing a character in the scanned data is multiplied by its corresponding digit in the

multiplier, and the sum of these products is computed. The check digit passes if this sum modulo check digit
modulus is zero.

Example:

Scanned data numeric value is 132456 (check digit is 6)
Check digit multiplier string is 123456

Digit 1

Multiplier 1

Product 1

Product add

1+ 6+ 6+ 16+ 25+ 36= 90

The check digit modulus is 10. It passes because 90 is divisible by 10 (the remainder is zero).

*No Check Digit

(0)

Product Add Left to Right

(3)

Summary of Contents for DS4800 Series







































































































































































































































































































































































































































Search results

Summary of Contents for DS4800 Series

Reviews:

Related manuals for DS4800 Series

Brands by name

Popular brands

Motorola DS4800 Series, Product Reference Manual

Search results

Summary of Contents for DS4800 Series

Reviews:

Related manuals for DS4800 Series

Brands by name

Popular brands