Motorola DS4800 Series Product Reference Manual Download | Manualshive

Page: 408 / 422

background image

Glossary - 8

DS4800 Series Corded Digital Imager Product Reference Guide

S

Scan Area.

Area intended to contain a symbol.

Scanner.

An electronic device used to scan bar code symbols and produce a digitized pattern that corresponds to the

bars and spaces of the symbol. Its three main components are: 1) Light source (laser or photoelectric cell) -
illuminates a bar code,; 2) Photodetector - registers the difference in reflected light (more light reflected from
spaces); 3) Signal conditioning circuit - transforms optical detector output into a digitized bar pattern.

Scanning Mode.

The scanner is energized, programmed and ready to read a bar code.

Scanning Sequence.

A method of programming or configuring parameters for a bar code reading system by scanning

bar code menus.

SDK.

Software Development Kit

Self-Checking Code.

A symbology that uses a checking algorithm to detect encoding errors within the characters of a

bar code symbol.

Shared Key.

Shared Key authentication is an algorithm where both the AP and the MU share an authentication key.

SHIP.

Symbol Host Interface Program.

SID.

System Identification code. An identifier issued by the FCC for each market. It is also broadcast by the cellular

carriers to allow cellular devices to distinguish between the home and roaming service.

Soft Reset.

See

Warm Boot

.

Space.

The lighter element of a bar code formed by the background between bars.

Specular Reflection.

The mirror-like direct reflection of light from a surface, which can cause difficulty decoding a bar

code.

Standard Trigger Mode.

The digital scanner uses this mode when lifted off the counter or removed from the wall mount.

In this mode, aim the digital scanner at a bar code and pull the trigger to decode.

Start/Stop Character.

A pattern of bars and spaces that provides the scanner with start and stop reading instructions

and scanning direction. The start and stop characters are normally to the left and right margins of a horizontal code.

STEP.

Symbol Terminal Enabler Program.

Subnet.

A subset of nodes on a network that are serviced by the same router. See

Router

.

Subnet Mask.

A 32-bit number used to separate the network and host sections of an IP address. A custom subnet mask

subdivides an IP network into smaller subsections. The mask is a binary pattern that is matched up with the IP
address to turn part of the host ID address field into a field for subnets. Default is often 255.255.255.0.

Substrate.

A foundation material on which a substance or image is placed.

SVTP.

Symbol Virtual Terminal Program.

Symbol.

A scannable unit that encodes data within the conventions of a certain symbology, usually including start/stop

characters, quiet zones, data characters and check characters.

«
...
406
407
408
409
410
...
»

Summary of Contents for DS4800 Series







































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DS4800 Series

Brand: SafeCom Pages: 30

Sentinel-Prox DC-1023

Brand: AWID Pages: 12

Brand: RTscan Pages: 28

PHOTO RESEARCH TRU 8

Brand: Jadak Pages: 9

Brand: Advanced Card Pages: 57

MSR 1218 SERIES

Brand: JARLTECH Pages: 18

Brand: Krüger & Matz Pages: 40

Brand: Samsung Pages: 36

Brand: Unitech Pages: 99

Brand: TSC Pages: 40

Brand: TSC Pages: 35

Prontronix TTP-244CE

Brand: TSC Pages: 36

Brand: TSC Pages: 48

TTP-286MT Series

Brand: TSC Pages: 63

Alpha-4L Series

Brand: TSC Pages: 35

Brand: Stid Pages: 3

Brand: Stid Pages: 10

Brand: Sven Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands