manualshive.com logo in svg

Motorola DSP56305, User Manual

The Motorola DSP56305 is a versatile digital signal processor designed for a wide range of applications. To get the most out of this powerful device, make sure to download the free User Manual from our website. Explore its features and functionalities with this comprehensive manual, available for instant download at 88.208.23.73:8080.

Share
Download
background image

CYCLIC CODE CO-PROCESSOR

CCOP Programming Model

MOTOROLA

DSP56305 User’s Manual

14-17

• the bits specified by the Bit Select registers CBSRA or CBSRB in Parity Coding 

Mode using two concatenated CFSRs (OPM[1:0] = 11)

In this case the processing is terminated (PREN is cleared and PCDN is set) and the Run 
Counter can be used to calculate the pointer to the erroneous burst in the data sequence 
that should be corrected. 

14.4.4.6

Force Shift bit (FOSH)—CCSR Bit 10

The FOrce SHift bit (FOSH) is a control bit used to force an unconditional extra shift in 
all CFSRs during a Cipher processing session. FOSH is operational in the Step-by-step 
Cipher mode only (OPM[1:0] = 01), and is ignored otherwise. When FOSH is cleared and 
a new step is activated (PREN is set), a single shift is executed to CFSRs selected 
according to the Step Function Table (if this step belongs to the run or output phase), the 
associated counter is decremented (which counter is decremented depends on which 
processing phase this particular step belongs to), and an output bit is generated (if this 
step belongs to the output phase). After this single step is accomplished PREN is 
automatically cleared causing CCOP to re-enter the Idle state. When FOSH is set and a 
new step is activated (PREN is set) a single shift is forced to all CFSRs independent of the 
Step Function Table. This extra shift can be inserted at any Cipher processing operating 
phase. It does not cause any counter decrement and (if executed in the output phase) 
does not generate an output bit to the output FIFO. Combining doing a single step with 
FOSH cleared and a single step with FOSH set accomplishes one step of the Cipher 
process in which the stepping function varies between 1 and 2 shifts instead of 0 and 1 
shift.

14.4.4.7

Data In Interrupt Enable bit (DIIE)—CCSR Bit 12

The Data In Interrupt Enable bit (DIIE), when set, enables the interrupt caused by the 
input FIFO empty signal (when the INFE bit, CCSR Bit 20, is set). When INFE is cleared, 
the interrupt is disabled.

14.4.4.8

Data Out Interrupt Enable bit (DOIE)—CCSR Bit 13

The Data Out Interrupt Enable bit (DOIE), when set, enables the interrupt caused by the 
output FIFO not empty signal (when the OFNE bit, CCSR Bit 21, is set). When OFNE is 
cleared, the interrupt is disabled.

14.4.4.9

Cipher Done Interrupt Enable bit (CDIE)—CCSR Bit 14

The Cipher Done Interrupt Enable bit (CDIE), when set, enables the interrupt caused by 
terminating CCOP Cipher mode processing (when CIDN, CCSR Bit 22, is set). If both 
CDIE and CIDN bits are set, the CCOP requests a Cipher Done interrupt request from 
the interrupt controller. When CDIE is cleared, the interrupt is disabled.

14.4.4.10

Parity Coding Done Interrupt Enable bit (PDIE)—CCSR Bit 15

The Parity Coding Done Interrupt Enable bit (PDIE), when set, enables the interrupt 
caused by terminating the CCOP Parity Coding mode processing (when PCDN, CCSR 

Summary of Contents for DSP56305

























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSP56305

Oberheim GM-1000 Operating Manual preview
GM-1000
Brand: Oberheim Pages: 84
Datavideo TWP-10 Instruction Manual preview
TWP-10
Brand: Datavideo Pages: 24
SIGNALCORE SC5520A Hardware Manual preview
SC5520A
Brand: SIGNALCORE Pages: 40
Moulinex Masterchef Gourmet QA408D Manual preview
Masterchef Gourmet QA408D
Brand: Moulinex Pages: 44
Moulinex cube & stick DJ905810 Manual preview
cube & stick DJ905810
Brand: Moulinex Pages: 42
Moulinex FP3181B2 Manual preview
FP3181B2
Brand: Moulinex Pages: 76
Kalorik USK MCH 33526 User Manual preview
USK MCH 33526
Brand: Kalorik Pages: 52
Waring WFP16SCD Owner'S Manual preview
WFP16SCD
Brand: Waring Pages: 35
Magic Bullet MBR03 User Manual preview
MBR03
Brand: Magic Bullet Pages: 21
Hamilton Beach 70450 - 6 Cup Bowl Food Processor Owner'S Manual preview
70450 - 6 Cup Bowl Food Processor
Brand: Hamilton Beach Pages: 40
Aplex AHM-6156P User Manual preview
AHM-6156P
Brand: Aplex Pages: 83
Coopers 9309 Instructions preview
9309
Brand: Coopers Pages: 2
Kenwood FP479 Manual preview
FP479
Brand: Kenwood Pages: 37
Toastmaster MJFP8W Owner'S Manual preview
MJFP8W
Brand: Toastmaster Pages: 18
VNS G-303 Quick User Manual preview
G-303
Brand: VNS Pages: 14
Philco PHSM 9000 User Manual preview
PHSM 9000
Brand: Philco Pages: 100
Estia basics 06-9922 Instruction Manual preview
basics 06-9922
Brand: Estia Pages: 16
Evalue Technology EES-3610 Series Quick Reference Manual preview
EES-3610 Series
Brand: Evalue Technology Pages: 32

Brands by name

Popular brands

Load more brands