MOTOROLA
DSP96002 USER’S MANUAL
2 - 1
SECTION 2
SIGNAL DESCRIPTION AND BUS OPERATION
2.1
PINOUT
The functional signal groups of the DSP96002 are shown in Figure 2-2, and are described in the following
sections. A pin allocation summary is shown in Figure 2-1. Specific pinout and timing information is avail-
able in the DSP96002 Technical Data Sheet (DSP96002/D).
2.1.1 Package
The DSP96002 is available in a 223 pin PGA package. There are 176 signal pins (including 5 spares), 17
power pins and 30 ground pins. All packaging information is available in the data sheet.
2.1.2 Interrupt And Mode Control (4 Pins)
—
R
—
E
—
S
—
E
–
T (Reset) - active low, Schmitt trigger input.
—
R
—
E
—
S
—
E
–
T is internally synchronized
to the input clock (CLK). When asserted, the chip is placed in the reset state and the
internal phase generator is reset. The Schmitt trigger input allows a slowly rising input
(such as a capacitor charging) to reliably reset the chip. If
—
R
—
E
—
S
—
E
–
T is deas-
serted synchronous to the input clock (CLK), exact startup timing is guaranteed, allow-
ing multiple processors to startup synchronously and operate together in "lock-step".
When the
—
R
—
E
—
S
—
E
–
T pin is deasserted, the initial chip operating mode is latched
from the MODA, MODB and MODC pins.
MODA/
—
I
—
R
—
Q
–
A(Mode Select A/External Interrupt Request A) - active low input, internally
synchronized to the input clock (CLK). MODA/
—
I
—
R
—
Q
–
A selects the initial chip
operating mode during hardware reset and becomes a level sensitive or negative edge
triggered, maskable interrupt request input during normal instruction processing.
MODA, MODB and MODC select one of 8 initial chip operating modes, latched into the
operating mode register (OMR) when the
—
R
—
E
—
S
—
E
–
T pin is deasserted. If
—
I
—
R
—
Q
–
A is asserted synchronous to the input clock (CLK), multiple processors can be
resynchronized using the WAIT instruction and asserting
—
I
—
R
—
Q
–
A to exit the wait
state. If the processor is in the STOP standby state and
—
I
—
R
—
Q
–
A is asserted, the
processor will exit the STOP state.
Summary of Contents for DSP96002
