manualshive.com logo in svg

Motorola MC68306, User Manual

The Motorola MC68306 User Manual is your comprehensive guide to maximizing the features of this powerful product. Download it for free from 88.208.23.73:8080 and gain access to easy-to-understand instructions, troubleshooting tips, and valuable insights to enhance your experience with the MC68306.

Share
Download
background image

MOTOROLA

MC68306 USER'S MANUAL

6-17

can be programmed to appear on output pin OP3 (inverted). The timer runs continuously
and cannot be stopped by the CPU. Because the timer cannot be stopped, the count
value (DUCUR/DUCLR) should not be read. When a read at the start counter command
address is performed, the timer terminates the current countdown sequence, clears its
output, reinitializes itself with the preload value, and begins a new countdown sequence.
Upon reaching $0000 (terminal count), the timer inverts its output, reinitializes itself with
the preload value, and repeats the countdown sequence. If the timer output toggled from
one to zero, the CTR/TMR_RDY bit (DUISR[3]) is also set. The timer can be programmed
to generate an interrupt request for this condition on the 

IRQ

 or 

TIRQ 

output. If the preload

value is changed by the CPU, the timer will not recognize the new value until it reaches
the next terminal count (and must reinitialize itself). This feature is very useful when
generating variable duty cycle square waves. When a read at the stop counter command
address is performed, the timer clears DUISR bit 3 but does not stop. Because in timer
mode the counter/timer runs continuously, it should be completely configured (preload
value loaded and start counter command issued) before programming the timer output to
appear on OP3.

6.3.6 Bus Operation

This section describes the operation of the bus during read, write, and interrupt
acknowledge cycles to the serial module. All serial module registers must be accessed as
bytes.

6.3.6.1 READ CYCLES. The serial module is accessed by the CPU with a variable
number of wait states, depending on the relative phase of the CPU and serial module
clocks. The maximum number of wait states for a 16.67 MHz CPU clock and 3.6864 MHz
serial module clock is six. The serial module responds to reads with byte data on D7–D0.
Reserved registers return logic zero during reads.

6.3.6.2 WRITE CYCLES. The serial module is accessed by the CPU with a variable
number of wait states, up to six. The serial module accepts write data on D7–D0. Write
cycles to read-only registers and reserved registers complete in a normal manner without
exception processing; however, the data is ignored.

6.3.6.3 INTERRUPT ACKNOWLEDGE CYCLES. The serial module is capable of
arbitrating for interrupt servicing and supplying the interrupt vector when it has
successfully won arbitration. The vector number must be provided if interrupt servicing is
necessary; thus, the interrupt vector register (DUIVR) must be initialized. If the DUIVR is
not initialized, a spurious interrupt exception will be taken if interrupts are generated.

6.4 REGISTER DESCRIPTION AND PROGRAMMING

This section contains a detailed description of each register and its specific function as
well as flowcharts of basic serial module programming.

6.4.1 Register Description

The operation of the serial module is controlled by writing control bytes into the
appropriate registers. A list of serial module registers and their associated addresses is

Summary of Contents for MC68306
































































































































































































Reviews:

No comments

Related manuals for MC68306

Blackrock Microsystems Cerebus Instructions For Use Manual preview
Cerebus
Brand: Blackrock Microsystems Pages: 27
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Brand: Dialogic Pages: 2
Parker PCH1 T P Series User Manual preview
PCH1 T P Series
Brand: Parker Pages: 107
Omron ACCURAX G5 - Quick Start Manual preview
ACCURAX G5 -
Brand: Omron Pages: 13
Medel RONDO 3 Quick Manual preview
RONDO 3
Brand: Medel Pages: 28
Riverbed SteelCentral AppResponse 2180 Upgrade And Maintenance Manual preview
SteelCentral AppResponse 2180
Brand: Riverbed Pages: 82
Advantech 3718HG User Manual preview
3718HG
Brand: Advantech Pages: 68
National Semiconductor Data Capture Board CLC-CAPT-PCASM User Manual preview
Data Capture Board CLC-CAPT-PCASM
Brand: National Semiconductor Pages: 15
Flexwatch FW3870 User Manual preview
FW3870
Brand: Flexwatch Pages: 13
audemat DIGIPLEXER 246 User Manual preview
DIGIPLEXER 246
Brand: audemat Pages: 93
Vxl IQL Series Hardware Installation Manual preview
IQL Series
Brand: Vxl Pages: 4
DataExpert ATX431 User Manual preview
ATX431
Brand: DataExpert Pages: 48
Aegis AVP-DE1K-100 User Manual preview
AVP-DE1K-100
Brand: Aegis Pages: 7
Epson C32C824151 - UB E02 Print Server Technical Reference Manual preview
C32C824151 - UB E02 Print Server
Brand: Epson Pages: 84
Epson C11CA31101 User Manual preview
C11CA31101
Brand: Epson Pages: 168
Epson B80818 Series Quick Manual preview
B80818 Series
Brand: Epson Pages: 3
Extron electronics Dual Window Multi-Graphic Processor MGP 462 Specifications preview
Dual Window Multi-Graphic Processor MGP 462
Brand: Extron electronics Pages: 2
Fujitsu PRIMEPOWER 1500 Manual preview
PRIMEPOWER 1500
Brand: Fujitsu Pages: 21

Brands by name

Popular brands

Load more brands