manualshive.com logo in svg

Motorola MC68306, User Manual

The Motorola MC68306 User Manual is your comprehensive guide to maximizing the features of this powerful product. Download it for free from 88.208.23.73:8080 and gain access to easy-to-understand instructions, troubleshooting tips, and valuable insights to enhance your experience with the MC68306.

Share
Download
background image

MOTOROLA

MC68306 USER'S MANUAL

1- 3

these instructions, including predecrement and postincrement, which allow simple stack
and queue maintenance and scaled indexing for efficient table accesses. Data types and
addressing modes are supported orthogonally by all data operations and with all
appropriate addressing modes. Position-independent code is easily written.

Like all M68000 family processors, the MC68EC000 core recognizes interrupts of seven
different priority levels and allows either an automatic vector or a peripheral-supplied
vector to direct the processor to the desired service routine. Internal trap exceptions
ensure proper instruction execution with good addresses and data, allow operating system
intervention in special situations, and permit instruction tracing. Hardware signals can
either terminate or rerun bad memory accesses before instructions process data
incorrectly. The EC000 core provides 2.4 MIPS at 16.67 MHz.

1.2 ON-CHIP PERIPHERALS

To improve total system throughput and reduce part count, board size, and cost of system
implementation, the M68300 family integrates on-chip, intelligent peripheral modules and
typical glue logic. The functions on the MC68306 include two serial channels, a
timer/counter, a DRAM controller, a parallel port, and system glue logic.

1.2.1 Serial Module

Most digital systems use serial I/O to communicate with host computers, operator
terminals, or remote devices. The MC68306 contains a two-channel, full-duplex UART
with an integrated timer. An on-chip baud rate generator provides standard baud rates up
the 38.4K baud to each channel's receiver and transmitter. The serial module is identical
to the MC68681/MC2681 DUART.

Each communication channel is completely independent. Data formats can be 5, 6, 7, or 8
bits with even, odd, or no parity and stop bits up to 2 in 1/16 increments. Four-byte receive
buffers and two-byte transmit buffers minimize CPU service calls. Each channel provides
a wide variety of error detection and maskable interrupt capability. Full-duplex, autoecho
loopback, local loopback, and remote loopback modes can be selected. Multidrop
applications are also supported.

A 3.6864 MHz crystal drives the baud rate generators. Each transmit and receive channel
can be programmed for a different baud rate. Full modem support is provided with
separate request-to-send (RTS) and clear-to-send (CTS) signals for each channel.

The integrated 16-bit timer/counter can operate in a counter mode or a timer mode. The
timer/counter can function as a system stopwatch, a real-time single interrupt generator,
or a device watchdog when in counter mode. In timer mode, the timer/counter can be
used as a programmable clock source for channels A and B, a periodic interrupt
generator, or a variable duty cycle square-wave generator.

1.2.2 DRAM Controller

DRAM is used in many systems since it is the least expensive form of high-speed storage
available. However, considerable design effort is often spent designing the interface

Summary of Contents for MC68306
































































































































































































Reviews:

No comments

Related manuals for MC68306

Samsung SWC-E100 Quick Start Manual preview
SWC-E100
Brand: Samsung Pages: 2
Samsung iDCS 500 Manual preview
iDCS 500
Brand: Samsung Pages: 31
Samsung DDR3 Product Manual preview
DDR3
Brand: Samsung Pages: 15
Data Translation DT330 Series Getting Started Manual preview
DT330 Series
Brand: Data Translation Pages: 60
Ebyte E43-900T13S3 Manual preview
E43-900T13S3
Brand: Ebyte Pages: 8
National Instruments NI 9426 Getting Started Manual preview
NI 9426
Brand: National Instruments Pages: 17
Patton electronics RocketLink-G 3088/I Getting Started Manual preview
RocketLink-G 3088/I
Brand: Patton electronics Pages: 61
Accusys ACS-76500 Owner'S Manual preview
ACS-76500
Brand: Accusys Pages: 34
Alesis QUADRAVERB Reference Manual preview
QUADRAVERB
Brand: Alesis Pages: 61
Intel 500 - DATASHEET REV 003 Datasheet preview
500 - DATASHEET REV 003
Brand: Intel Pages: 67
Vega ARIES v3.0 Product Reference Manual preview
ARIES v3.0
Brand: Vega Pages: 12
ADS Technologies API-800 Installation Manual preview
API-800
Brand: ADS Technologies Pages: 21
ICP ICP9014RO Installation And User Manual preview
ICP9014RO
Brand: ICP Pages: 142
CyberResearch CPBF PMX-233 User Manual preview
CPBF PMX-233
Brand: CyberResearch Pages: 59
Omega Engineering BNC-08DI, BNC-16DI, BNC-16SE User Manual preview
BNC-08DI, BNC-16DI, BNC-16SE
Brand: Omega Engineering Pages: 25
Hawking WIRELESS-G CARDBUS PC CARD - GUIDE D User Manual preview
WIRELESS-G CARDBUS PC CARD - GUIDE D
Brand: Hawking Pages: 26
Dvico FusionHDTV 5 GOLD User Manual preview
FusionHDTV 5 GOLD
Brand: Dvico Pages: 64
EKF 82600 User Manual preview
82600
Brand: EKF Pages: 40

Brands by name

Popular brands

Load more brands