MOTOROLA
Chapter 20. SCC UART Mode
20-17
Part IV. Communications Processor Module
Figure 20-8 shows the SCC UART RxBD.
Table 20-10 describes RxBD status and control Þelds.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0
E
Ñ
W
I
C
A
CM
ID
AM
Ñ
BR
FR
PR
Ñ
OV
CD
2
Data Length
4
Rx Buffer Pointer
6
Figure 20-8. SCC UART Receive Buffer Descriptor (RxBD)
Table 20-10. SCC UART RxBD Status and Control Field Descriptions
Bits Name
Description
0
E
Empty.
0 The buffer is full or reception was aborted due to an error. The core can read or write to any Þelds of
this BD. The CPM does not reuse this BD while E = 0.
1 The buffer is not full. The CPM controls this BD and buffer. The core should not modify this BD.
1
Ñ
Reserved, should be cleared.
2
W
Wrap (last buffer descriptor in the BD table).
0 Not the last descriptor in the table.
1 Last descriptor in the table. After this buffer is used, the CPM receives incoming data using the BD
pointed to by RBASE. The number of BDs in this table is programable and determined only by the W
bit and overall space constraints of the dual-port RAM.
3
I
Interrupt.
0 No interrupt is generated after this buffer is Þlled.
1 The CP sets SCCE[RX] when this buffer is completely Þlled by the CPM, indicating the need for the
core to process the buffer. Setting SCCE[RX] causes an interrupt if not masked.
4
C
Control character.
0 This buffer does not contain a control character.
1 The last byte in this buffer matches a user-deÞned control character.
5
A
Address.
0 The buffer contains only data.
1 For manual multidrop mode, A indicates the Þrst byte of this buffer is an address byte. Software should
perform address comparison. In automatic multidrop mode, A indicates the buffer contains a message
received immediately after an address matched UADDR1 or UADDR2. The address itself is not written
to the buffer but is indicated by the AM bit.
6
CM
Continuous mode.
0 Normal operation. The CPM clears E after this BD is closed.
1 The CPM does not clear E after this BD is closed, allowing the buffer to be overwritten when the CPM
accesses this BD again. E is cleared if an error occurs during reception, regardless of CM.
7
ID
Buffer closed on reception of idles. The buffer is closed because a programmable number of consecutive
idle sequences (MAX_IDL) was received.
8
AM
Address match. SigniÞcant only if the address bit is set and automatic multidrop mode is selected in
PSMR[UM]. After an address match, AM identiÞes which user-deÞned address character was matched.
0 The address matched the value in UADDR2.
1 The address matched the value in UADDR1.
9
Ñ
Reserved, should be cleared.
Summary of Contents for MPC8260 PowerQUICC II
