manualshive.com logo in svg

Motorola MPC8260 PowerQUICC II, User Manual

The Motorola MPC8260 PowerQUICC II is a cutting-edge embedded processor, designed to deliver superior performance and efficiency. To fully explore the extensive features and capabilities of this advanced product, be sure to download the comprehensive User Manual for free from our website 88.208.23.73:8080.

Share
Download
background image

MOTOROLA

Chapter 26.  Serial Management Controllers (SMCs)

  

26-13

Part IV.  Communications Processor Module

Table 26-5 describes receive commands issued to the CPCR.

26.3.6  Sending a Break

A break is an all-zeros character without stop bits. It is sent by issuing a 

STOP

 

TRANSMIT

command. After sending any outstanding data, the SMC sends a character of consecutive
zeros, the number of which is the sum of the character length, plus the number of start,
parity, and stop bits. The SMC sends a programmable number of break characters
according to BRKCR and then reverts to idle or sends data if a 

RESTART

 

TRANSMIT

 is issued

before completion. When the break completes, the transmitter sends at least one idle
character before sending any data to guarantee recognition of a valid start bit. 

26.3.7  Sending a Preamble

A preamble sequence provides a way to ensure that the line is idle before a new message
transfer begins. The length of the preamble sequence is constructed of consecutive ones that
are one-character long. If the preamble bit in a BD is set, the SMC sends a preamble
sequence before sending that buffer. For 8 data bits, no parity, 1 stop bit, and 1 start bit, a
preamble of 10 ones would be sent before the Þrst character in the buffer. If no preamble
sequence is sent, data from two ready transmit buffers can be sent on the transmit signal
with no delay between them.

26.3.8  Handling Errors in the SMC UART Controller

The SMC UART controller reports character reception error conditions via the channel
BDs and the SMCE. The SMC UART controller has no transmission errors.

Table 26-5. Receive Commands

Command Description

ENTER

 

HUNT

 

MODE

Use the 

CLOSE

 

RXBD

 command instead 

ENTER

 

HUNT

 

MODE

 for an SMC UART channel. 

CLOSE

 

RXBD

Forces the SMC to close the current receive BD if it is currently being used and to use the next BD 
in the list for any subsequently received data. If the SMC is not receiving data, no action is taken.

INIT

 

RX

 

PARAMETERS

Initializes receive parameters in this serial channel parameter RAM to reset state. Issue it only if 
the receiver is disabled. 

INIT

 

TX

 

AND

 

RX

 

PARAMETERS

 resets both receive and transmit parameters.

Table 26-6. SMC UART Errors 

Error

Description

Overrun

The SMC maintains a two-character length FIFO for receiving data. Data is moved to the buffer after the 
Þrst character is received into the FIFO; if a receiver FIFO overrun occurs, the channel writes the 
received character into the internal FIFO. It then writes the character to the buffer, closes it, sets the OV 
bit in the BD, and generates the RXB interrupt if it is enabled. Reception then resumes as normal. 
Overrun errors that occasionally occur when the line is idle can be ignored.

Parity

The channel writes the received character to the buffer, closes it, sets the PR bit in the BD, and 
generates the RXB interrupt if it is enabled. Reception then resumes as normal.

Idle 
Sequence 
Receive

An idle is found when a character of all ones is received, at which point the channel counts consecutive 
idle characters. If the count reaches MAX_IDL, the buffer is closed and an RXB interrupt is generated. If 
no receive buffer is open, this does not generate an interrupt or any status information. The idle counter 
is reset each time a character is received.

Summary of Contents for MPC8260 PowerQUICC II















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC8260 PowerQUICC II

Palo Alto Network M-200 Reference Manual preview
M-200
Brand: Palo Alto Network Pages: 56
XESS XStend XS40 User Manual preview
XStend XS40
Brand: XESS Pages: 23
ETAS FETK-S2.1 User Manual preview
FETK-S2.1
Brand: ETAS Pages: 69
IBA Com-L2B-4-8 Manual preview
Com-L2B-4-8
Brand: IBA Pages: 29
Stanwax Laser S4i Manual preview
S4i
Brand: Stanwax Laser Pages: 9
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Brand: IDT Pages: 11
Qlogic QLE7xxx Series Quick Start Manual preview
QLE7xxx Series
Brand: Qlogic Pages: 8
ZALMAN ZM-RF1 User Manual preview
ZM-RF1
Brand: ZALMAN Pages: 5
4gon RouterBOARD 411R Quick Start Manual preview
RouterBOARD 411R
Brand: 4gon Pages: 2
Idis DR-1508P Operation Manual preview
DR-1508P
Brand: Idis Pages: 85
Giacomini KPM36Y002 Manual preview
KPM36Y002
Brand: Giacomini Pages: 2
Lanner NCA-1040 User Manual preview
NCA-1040
Brand: Lanner Pages: 59
ZALMAN CNPS7000A Series User Manual preview
CNPS7000A Series
Brand: ZALMAN Pages: 9
WABCO CAN Router Manual preview
CAN Router
Brand: WABCO Pages: 29
ADTRAN EXPRESS 6503 User Manual preview
EXPRESS 6503
Brand: ADTRAN Pages: 20
Keithley DAS-1800HR Series User Manual preview
DAS-1800HR Series
Brand: Keithley Pages: 139
Multi-Link Power Stone Programming Manual preview
Power Stone
Brand: Multi-Link Pages: 31
MicroNova O047 Technical Installation Manual preview
O047
Brand: MicroNova Pages: 113

Brands by name

Popular brands

Load more brands