manualshive.com logo in svg

Motorola MPC8260 PowerQUICC II, User Manual

The Motorola MPC8260 PowerQUICC II is a cutting-edge embedded processor, designed to deliver superior performance and efficiency. To fully explore the extensive features and capabilities of this advanced product, be sure to download the comprehensive User Manual for free from our website 88.208.23.73:8080.

Share
Download
background image

MOTOROLA

Chapter 31.  FCC HDLC Controller

  

31-7

Part IV.  Communications Processor Module

Table 31-5 describes HDLC reception errors, which are reported through the RxBD.

31.6  HDLC Mode Register (FPSMR)

When an FCC is conÞgured for HDLC mode, the FPSMR is used as the HDLC mode
register, shown in Figure 31-3. 

Table 31-5. HDLC Reception Errors 

Error Description

Overrun Error  The HDLC controller maintains an internal FIFO buffer for receiving data. The CP begins 

programming the SDMA channel and updating the CRC whenever data is received in the FIFO buffer. 
When a receive FIFO overrun occurs, the channel writes the received data byte to the internal FIFO 
buffer over the previously received byte. The previous byte and the frame status are lost. The channel 
closes the buffer with RxBD[OV] set and generates the RXF interrupt if it is enabled. The receiver then 
enters hunt mode. Even if the overrun occurs during a frame whose address is not matched in the 
address recognition logic, an RxBD with data length two is opened to report the overrun and the RXF 
interrupt is generated if it is enabled.

CD Lost 
During Frame 
Reception

 

When this error occurs, the channel terminates frame reception, closes the buffer, sets RxBD[CD], 
and generates the RXF interrupt if it is enabled. This error has highest priority. The rest of the frame is 
lost and other errors are not checked in that frame. At this point, the receiver enters hunt mode.

Abort 
Sequence

 

The HDLC controller detects an abort sequence when seven or more consecutive ones are received. 
When this error occurs and the HDLC controller receives a frame, the channel closes the buffer by 
setting RxBD[AB] and generates the RXF interrupt (if enabled). The channel also increments the abort 
sequence counter. The CRC and nonoctet error status conditions are not checked on aborted frames. 
The receiver then enters hunt mode. When an abort sequence is received, the user is given no 
indication that an HDLC controller is not currently receiving a frame.

Nonoctet 
Aligned Frame

 

When this error occurs, the channel writes the received data to the data buffer, closes the buffer, sets 
the Rx nonoctet aligned frame bit RxBD[NO], and generates the RXF interrupt (if it is enabled). The 
CRC error status should be disregarded on nonoctet frames. After a nonoctet aligned frame is 
received, the receiver enters hunt mode. An immediate back-to-back frame is still received. The 
nonoctet data portion may be derived from the last byte in the buffer by Þnding the least-signiÞcant set 
bit, which marks the end of valid data as follows:

msb

lsb

Valid data

1

0

0

0

CRC Error

When this error occurs, the channel writes the received CRC to the data buffer, closes the buffer, sets 
RxBD[CR], and generates the RXF interrupt (if it is enabled). The channel also increments the CRC 
error counter. After receiving a frame with a CRC error, the receiver enters hunt mode. An immediate 
back-to-back frame is still received. CRC checking cannot be disabled, but the CRC error can be 
ignored if checking is not required.

Summary of Contents for MPC8260 PowerQUICC II















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC8260 PowerQUICC II

Lauterbach C2000 Manual preview
C2000
Brand: Lauterbach Pages: 61
Zhone 6211 Quick Installation Instructions preview
6211
Brand: Zhone Pages: 1
Aruba IntroSpect Analyzer 2 Series Quick Start Manual preview
IntroSpect Analyzer 2 Series
Brand: Aruba Pages: 5
red lion Yaskawa 2000 Information Sheet preview
Yaskawa 2000
Brand: red lion Pages: 5
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Brand: Softing Pages: 4
Idis DR-1508P Operation Manual preview
DR-1508P
Brand: Idis Pages: 85
Digi ConnectCore 8X Hardware Reference Manual preview
ConnectCore 8X
Brand: Digi Pages: 116
ST X-NUCLEO-EEPRMA1 User Manual preview
X-NUCLEO-EEPRMA1
Brand: ST Pages: 22
LST ZEB2-1 Specifications preview
ZEB2-1
Brand: LST Pages: 1
Alphacool EISBAER PRO Quick Start Manual preview
EISBAER PRO
Brand: Alphacool Pages: 9
Supermicro BPN-SAS3-LB16A-N10 User Manual preview
BPN-SAS3-LB16A-N10
Brand: Supermicro Pages: 11
Hanwha Techwin WISENET XRN-1610 User Manual preview
WISENET XRN-1610
Brand: Hanwha Techwin Pages: 88
FabiaTech FB2701 User Manual preview
FB2701
Brand: FabiaTech Pages: 86
Opengear OG-HDTV-SDI-UHD User Manual preview
OG-HDTV-SDI-UHD
Brand: Opengear Pages: 7
Multitech FaxFinder FF-120 Administrator User Manual preview
FaxFinder FF-120
Brand: Multitech Pages: 20
Renesas Emulation Probe M306V8T-EPB User Manual preview
Emulation Probe M306V8T-EPB
Brand: Renesas Pages: 90
A.E.B. 628450000 Assembly & Instruction Manual preview
628450000
Brand: A.E.B. Pages: 10
Aegis AVP-DE1K-100 User Manual preview
AVP-DE1K-100
Brand: Aegis Pages: 7

Brands by name

Popular brands

Load more brands