5 - 94 WiNG 5.7.1 Access Point System Reference Guide
6. Set the following
OSPF Overload Protection
settings:
7. Set the following
Default Information
:
8. Refer to the
Route Redistribution
table to set the types of routes that can be used by OSPF.
Select the
+ Add Row
button to populate the table. Set the
Route Type
used to define the redistributed route. Options
include
connected
,
kernel
and
static
.
Select the
Metric Type
option to define the exterior metric type (1 or 2) used with the route redistribution. Select the
Metric
option to define route metric used with the redistributed route.
9. Use the
OSPF Network
table to define networks (IP addresses) to connect using dynamic routes.
Select the
+ Add Row
button to populate the table. Add the IP address and mask of the
Network(s)
participating in OSPF.
Additionally, define the OSPF area (IP address) to which the network belongs.
10. Set an
OSPF Default Route Priority
(1 - 8,000) as the priority of the default route learnt from OSPF.
11. Select the
Area Settings
tab.
An OSPF
Area
contains a set of routers exchanging
Link State Advertisements
(LSAs) with others in the same area. Areas
limit LSAs and encourage aggregate routes.
VRRP State Check
Select this option to enable checking VRRP state. If the interface’s VRRP state is not
Backup
, then the interface is published via OSPF.
Number of Routes
Use the spinner controller to set the maximum number of OSPN routes permitted. The
available range is from 1 - 4,294,967,295.
Retry Count
Set the maximum number of retries (OSPF resets) permitted before the OSPF process is
shut down. The available range is from 1 - 32. The default setting is 5.
Retry Time Out
Set the duration (in seconds) the OSPF process remains off before initiating its next
retry. The available range is from 1 - 3,600 seconds. The default is 60 seconds.
Reset Time
Set the reset time (in seconds) that, when exceeded, changes the retry count is zero.
The available range is from 1 - 86,400. The default is 360 seconds.
Originate
Select this option to make the default route a distributed route. This setting is disabled
by default.
Always
Enabling this setting continuously maintains a default route, even when no routes
appear in the routing table. This setting is disabled by default.
Metric Type
Select this option to define the exterior metric type (1 or 2) used with the default route.
Route Metric
Select this option to define route metric used with the default route. OSPF uses path
cost as its routing metric. It is defined by the speed (bandwidth) of the interface
supporting a given route.
Summary of Contents for WiNG 5.7.1
