5 - 311
11. Set or override the following
Web Filter
parameters. Web filters are used to control access to resources on the Internet.
12. Set or override the following
Extended VLAN Tunnel
parameters:
13. Set the following
Tunnel Rate Limit
parameters:
URL Filter
Use the drop-down menu to select a URL filter to use with this Bridge VLAN.
L2 Tunnel Broadcast
Optimization
Select this option to enhance (optimize) layer 2 traffic broadcast packet transmissions. This
setting is disabled by default.
Bridging Mode
Specify one of the following bridging mode for use on the VLAN:
•
Automatic
- Select automatic mode to let the controller or service platform determine the
best bridging mode for the VLAN.
•
Local
- Select Local to use local bridging mode for bridging traffic on the VLAN.
•
Tunnel -
Select Tunnel to use a shared tunnel for bridging traffic on the VLAN.
•
Isolated Tunnel
- Select isolated-tunnel to use a dedicated tunnel for bridging traffic on
the VLAN.
IP Outbound Tunnel
ACL
Select an
IP Outbound Tunnel ACL
for outbound traffic from the drop-down menu. If an
appropriate outbound IP ACL is not available, select the
Create
button.
IPv6 Outbound Tunnel
ACL
Select an
IPv6 Outbound Tunnel ACL
for outbound traffic from the drop-down menu. If an
appropriate outbound IPv6 ACL is not available, select the
Create
button.
MAC Outbound Tunnel
ACL
Select a
MAC Outbound Tunnel ACL
for outbound traffic from the drop-down menu. If an
appropriate outbound MAC ACL is not available, select the
Create
button.
Tunnel Over Level 2
Select this option to allow VLAN traffic to be tunneled over level 2 links. This setting is
disabled by default.
NOTE:
If creating a mesh connection between two access points in Standalone AP
mode,
Tunnel
must be selected as the bridging mode to successfully create the mesh link
between the two access points.
Mint Link Level
Select the MINT link level from the drop-down menu.
Rate
Define a transmit rate limit between 50 - 1,000,000 kbps. This limit constitutes a threshold
for the maximum the number of packets transmitted or received over the Bridge VLAN.
Traffic that exceeds the defined rate is dropped and a log message is generated. The default
setting is 5,000 kbps.
Maximum Burst Size
Set a maximum burst size between 0 - 1024 kbytes. The smaller the burst, the less likely the
receive packet transmission will result in congestion. The default burst size is 320 kbytes.
Background
Set the random early detection threshold in % for background traffic. Set a value from 1 -
100%. The default is 50%.
Best-effort
Set the random early detection threshold in % for best-effort traffic. Set a value from 1 -
100%. The default is 50%.
Summary of Contents for WiNG 5.7.1
