it has changed enough. If not, repeat steps 3 & 4 until the proper tension
is achieved.
5. Tighten the axle nuts to 15 ft lbs.
NOTE: To loosen the chain tension, follow the steps above except turn the ten-
sioner bolts counter-clockwise (outward) to loosen.
The drive chain on your MBxXSe must be kept lubricated often to avoid
excessive wear. To lubricate the drive chain, follow the steps below:
1. Park the bike on a level, flat surface using the kickstand.
2. Lean the bike toward the kickstand so that the rear wheel comes off
the ground an inch or two.
3. As you rotate the rear tire, wipe down the chain with a clean cloth to
remove as much grime and build up as possible.
3. Again rotating the rear tire, spray a good chain lubricant on the chain
so that the full length of the chain is lubricated. Use any spray lube, a
household oil like 3-in-1 oil, or any bicycle-specific chain lube.
Spray solvents like WD-40 are not recommended as they tend to dilute
and remove oil from the chains.
4. Using a cloth, wipe off the excess lube.
NOTE: The chain should be thoroughly lubricated but without buildup of lube,
which can collect dirt and grit which causes damage to the chain.
The MBxXSe is equipped with a 30-amp fuse to protect the system in the
event of electrical shorts. When a short or overload in the system occurs, the
fuse activates which will protect the wiring and help to avoid possible fire.
Possible situations that can result in a blown fuse can be:
1. A worn or pinched wire in the system that causes a short.
2. Moisture in the system.
3. Overloaded electrical system.
In the event of a burned-out fuse, your MBxXSe will not work when you turn
it on and the indicator lights will not light up. To check and/or replace the
fuse, follow the steps on the following page:
1. Open the plastic battery case by removing
both knob screws (on the front and back
of the battery case) and pulling the right
side panel off.
2. Locate the black rubber fuse housing, in
the wiring above the battery.
3. Open the rubber flip top lid and carefully
pull out the fuse.
4. Inspect the fuse and replace if necessary.
5. Re-assemble the fuse holder and the body
case, making sure it is clean and dry inside
and that all the wiring is safely tucked
inside. Watch carefully for pinched wires.
NOTE: IF THE FUSE CONTINUES TO BURN
OUT YOU HAVE ENCOUNTERED AN
ELECTRICAL PROBLEM. CSTOP USING THE
BIKE AND CALL MOTOVOX AT
888-488 MOTO (6686) OR EMAIL US AT
INFO@MOTOVOX.COM FOR ASSISTANCE.
The MBxXSe is equipped with a mechanical rear disc brake system. You
should check the brake and make sure it is working properly before each
ride. The brake should feel firm when the lever is pulled and you should not
be able to pull the brake lever all the way back to where it touches the hand
grip. If you can squeeze the brake lever all the way to the hand grip, your
brake needs adjusting. There are two options to adjust the brakes:
OPTION 1: Adjust using the barrel roller.
1. Loosen the set ring on the barrel adjuster.
2. Screw the barrel adjuster out a few turns
and then check the tension in the lever.
3. If it feels right, re-tighten the set ring.
4. If not, repeat step 2 until the brake feels
right and then tighten the set ring nut.
MAINTAINING YOUR MINI BIKE
17
16
MAINTENANCE
DRIVE CHAIN TENSION (CONTINUED)
LUBRICATING THE DRIVE CHAIN
REPLACING THE FUSE
ADJUSTING THE BRAKE
MAINTAINING YOUR MINI BIKE
TROUBLE
?
DO NOT RETURN TO STORE
contact us!
888-488-MOTO (6686)
or email info@motovox.com
Barrel Roller
Rear Knob Screw
Set Ring
