manualshive.com logo in svg

MOTU PCI-424, User Manual

Looking for the User Manual for the MOTU PCI-424? Look no further! You can easily download the comprehensive manual for free from our website. Gain a thorough understanding of your product's features, setup, and troubleshooting tips. Visit 88.208.23.73:8080 and get your manual now!

Share
Download
background image

CHAPTER

17

1

About the PCI-424 System

OVERVIEW

The PCI-424 core system is a computer-based hard 
disk recording system for Mac OS and Windows 
that offers 24 simultaneous inputs and outputs per 
Audio Wire cable, expandable to 96 
inputs/outputs. A core system consists of a PCI 
card connected to a standard 19-inch, 
single-space, rack-mountable audio interface.

The system includes AudioDesk™, full-featured 
audio workstation software for Mac OS that 
supports both 16-bit and 24-bit recording at any 
standard sample rate up to 192 kHz.

For Windows, a WDM driver is included for 
compatibility with audio applications that support 
standard multi-channel WDM and Wave drivers.

Also included are Macintosh and Windows ASIO 
drivers for multi-channel operation with Steinberg 
Cubase and other ASIO-compatible software.

A note about Mac OS X

This manual covers the operation of the PCI-424 
system under Mac OS 9. Visit www.motu.com for 
the latest information about using the PCI-424 
system with Mac OS X.

The PCI-424 card  . . . . . . . . . . . . . . . . . . . . . . . . . .17

The 2408mk3 interface. . . . . . . . . . . . . . . . . . . . . .18

The 24I/O interface. . . . . . . . . . . . . . . . . . . . . . . . .20

The HD192 interface  . . . . . . . . . . . . . . . . . . . . . . .20

16-bit and 24-bit recording . . . . . . . . . . . . . . . . . .21

AudioDesk  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Digital Performer  . . . . . . . . . . . . . . . . . . . . . . . . . .21

Other Audio Software. . . . . . . . . . . . . . . . . . . . . . .21

A computer-based system . . . . . . . . . . . . . . . . . . .21

THE PCI-424 CARD

A PCI-424 core system ships with a single PCI 
audio card called the PCI-424. The card features a 
custom processor, a powerful DSP chip, four 6-pin 
Audio Wire connectors and an ADAT SYNC IN 
connector.

High definition audio

The PCI-424 system can operate at the following 
high sample rates: 44.1, 48, 88.2, 96, 176.4 and 192 
kHz. All MOTU PCI-424 audio interfaces support 
rates up to 96 kHz. In addition, the HD192 
interface offers analog recording and playback at 
176.4 or 192 kHz.

Audio Wire expansion

The PCI-424 card provides four Audio Wire jacks, 
which are used to attach MOTU PCI audio 
interfaces to the card installed in the computer. 
Each Audio Wire is capable of transmitting 24 
simultaneous channels of 96 kHz digital audio 
input and output or 12 simultaneous channels of 
192 kHz input and output.

Up to four MOTU PCI audio interfaces can be 
connected to a single PCI-424 card for a maximum 
of 96 possible input and output connections. All 
MOTU PCI audio interfaces (including the 
2408mk3, 24I/O and HD192) can also be “mixed 
and matched” on the PCI-424 card, along with 
legacy PCI-324 interfaces, such as the 2408, 
2408mII, 1296, 1224, 24i and 308.

Audio Wire carries a proprietary communication 
protocol between the card and the external I/O to 
handle the extremely low latencies required by the 
system. The heart of the PCI-424 card is a 
custom-programmed VLSI chip capable of simul-
taneously processing all 96 inputs and outputs (192 

Summary of Contents for PCI-424















































































































































































































































































Reviews:

No comments

Related manuals for PCI-424

EVGA GeForce GTX 560 Superclocked Specifications preview
GeForce GTX 560 Superclocked
Brand: EVGA Pages: 1
Evolveo NVME PCIe x16 Manual preview
NVME PCIe x16
Brand: Evolveo Pages: 19
Diamond Multimedia SM56PCI Quick Start Manual preview
SM56PCI
Brand: Diamond Multimedia Pages: 6
Syris SYRD245-1W User Manual preview
SYRD245-1W
Brand: Syris Pages: 7
Intratone 04-0106-EN Wiring Diagram preview
04-0106-EN
Brand: Intratone Pages: 2
Intratone 04-0108 Quick Start Manual preview
04-0108
Brand: Intratone Pages: 4
Rosslare AY-V64B Installation And Programming Manual preview
AY-V64B
Brand: Rosslare Pages: 25
Newer Technology MAXPower Quick Installation Manual preview
MAXPower
Brand: Newer Technology Pages: 49
Kanguru Slim FC-RW User Manual preview
Slim FC-RW
Brand: Kanguru Pages: 29
Diablotek V5500-128A Specification preview
V5500-128A
Brand: Diablotek Pages: 1
Adaptec AVA-2906 Installation Manual preview
AVA-2906
Brand: Adaptec Pages: 24
Gainward 8400GS 1GB DVI HDMI Brochure preview
8400GS 1GB DVI HDMI
Brand: Gainward Pages: 2
3Com WL-549 User Manual preview
WL-549
Brand: 3Com Pages: 28
Naigon Electronics Igniter 3 Setup Manual preview
Igniter 3
Brand: Naigon Electronics Pages: 42
Commell MP-6100 User Manual preview
MP-6100
Brand: Commell Pages: 13
Digitus DA-70856 User Manual preview
DA-70856
Brand: Digitus Pages: 4
Xceed ID XF1100 Installation Sheet preview
XF1100
Brand: Xceed ID Pages: 3
StarTech.com PEX2S953LP Quick Start Manual preview
PEX2S953LP
Brand: StarTech.com Pages: 2

Brands by name

Popular brands

Load more brands