MOTU PCI-424 User Manual Download | Manualshive

Page: 81 / 270

background image

I N S T A L L I N G T H E P C I - 4 2 4 H A R D W A R E

52

SYNC FOR 2408MK3 STAND-ALONE
OPERATION

The 2408mk3 interface goes into

stand-alone

mode

whenever it is not under control of the PCI-424
software driver. In other words, whenever there
isn’t any 2408mk3-related software running on the
computer, the 2408mk3 I/O will operate as a stand-
alone format converter.

For further details about this, see chapter 5,
“2408mk3 Front Panel Operation” (page 55).

In most cases, when the 2408mk3 is performing
stand-alone format conversion, the source of the
transfer should serve as the clock source. Many of
the synchronization scenarios already discussed in
this chapter can be used. Below is a summary. For
details on how to make these settings from the
front panel, see “Clock” on page 58 and “Source”
on page 60.

Front panel SOURCE setting

Front panel CLOCK setting

Required sync connections

ADAT Bank A

Dig (Digital)

ADAT optical
(OUT from the source device
to IN on the 2408mk3)

ADAT Bank B

Dig (Digital)

same as above

ADAT Bank C

Dig (Digital)

same as above

ADAT Bank A, B, C

Dig (Digital)

same as above

Tascam A

Wrd (word clock) (with no synchronizer)

OR

PCI
(Use

PCI

if the 2408mk3 is slaved to a synchronizer

via ADAT sync on the PCI-424 card, and the
Tascam source is also slaved to the synchronizer)

Note: Tascam itself cannot be used as the clock
source, since TDIF carries no clock

Figure 4-29 on page 49

Tascam B

Same as above

Figure 4-29 on page 49

Tascam C

Same as above

Figure 4-29 on page 49

Tascam A, B, C

Same as above

Figure 4-29 on page 49

SPDIF

Dig (Digital)

OR

Wrd (Word clock)

Figure 4-30 on page 50

Analog

Any setting that synchronizes the 2408mk3
with the destination format

ADAT: Figure 4-28 on page 48
Tascam: Figure 4-29 on page 49
SPDIF: Figure 4-30 on page 50

«
...
79
80
81
82
83
...
»

Summary of Contents for PCI-424















































































































































































































































































Reviews:

No comments

Related manuals for PCI-424

Brand: ICP DAS USA Pages: 6

SKU 4670PE31GDT

Brand: Diamond Multimedia Pages: 1

Brand: Barkodes Pages: 9

Brand: Digital Equipment Pages: 36

Brand: Aaeon Pages: 55

Brand: Hauppauge Pages: 2

Brand: Advantech Pages: 38

Brand: Loopcomm Pages: 2

Brand: Kobil Pages: 3

N-FXE-02 Series

Brand: Transition Networks Pages: 5

Brand: ADLINK Technology Pages: 53

The VisionAV-SDI

Brand: Datapath Pages: 14

Brand: Decision-Computer Pages: 8

Brand: Verifi Pages: 8

GT240 512MB GDDR3

Brand: Gainward Pages: 2

Brand: Gear Head Pages: 8

Brand: E-Films Pages: 8

ControlSpace ESPLink

Brand: Bose Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands