background image

14

99286GB- XMODE – USER MANUAL - REV. 01

11.1 - DOUBLE TUBE VERSION (Art. 99.703)  

To replace the batteries, open the door and insert a screwdriver (or a coin) in the notches on the two covers. Press gently and turn them counter-
clockwise until they come out, as shown in the figure. Remove the batteries (three in each tube). If the bottom battery doesn’t come out, press on 
it gently with the screwdriver and release it suddenly so that the spring (which pushes from behind the battery) will expel it completely. Replace 
the batteries, inserting them with the negative pole (-) in the direction of insertion and the positive pole (+) facing the cover.

When insertion is done, close the covers by repeating the above steps in the reverse order.

10 - MAINS POWER SUPPLY

11 - BATTERY POWER SUPPLY

If the lock is powered from the MAINS, you have to use an appropriately sized transformer.
The MOTTURA transformer (AC/DC Adapter option Art. 99.683 with cable Art. 99697) was subjected to tests on the lock to obtain the legally 
required certifications regarding immunity from electrical and electromagnetic noise as well as emissions to the mains and to the environment. 
Therefore, it must be used to power lock versions that require a transformer.
The use of any transformer other than the one supplied (even for temporary testing), in addition to creating risk of damaging the lock or causing 
malfunctions, will immediately void all warranties. Mottura serrature di sicurezza S.p.A. will assume no liability for any harm/damage caused to 
persons or property.

If the lock is powered by BATTERIES, you have to use a battery pack (option Art. 99.703 or Art. 99.704) plus a battery charger (option Art. 99.711 
with cable Art. 99.712) if rechargeable batteries are used. The system automatically checks the battery charge level at the start of every cycle. 
When the batteries are near the minimum level sufficient to ensure correct functioning of the lock, 3 beeps and lighting of the YELLOW LED on the 
internal escutcheon remind you to replace them. In this condition, correct operation of the lock and correct scanning of transponder keys are not 
guaranteed. When the battery charge is no longer sufficient to operate the lock, a double high-low sound and lighting of the YELLOW LED require 
their replacement. In any case, you should replace the batteries once a year. 
Follow these instructions when replacing the batteries:

Never use rechargeable batteries if your system requires non-rechargeable (alkaline) batteries. Doing so will compromise operation of 
the lock. Never use non-rechargeable (alkaline) batteries if your system requires rechargeable batteries. Doing so will create risks of 

overheating, bursting, and acid leaks.
Mottura serrature di sicurezza S.p.A. assumes no liability for any type of malfunction, fault, and harm/damage caused to persons or 

property deriving from failure to observe the following instructions, which will also void the warranty.

For non-rechargeable alkaline batteries

 - 6x1.5V type D (flashlight): replace all alkaline batteries promptly (or at least once a year) as soon as the 

lock signals that their charge is insufficient to prevent electronic malfunction, failure to open the door, or damage.

For rechargeable NiMH batteries

 - 6x1.2V NiMH 2200mAh D (flashlight): use the Mottura code 99.711 battery charger and promptly replace all 

rechargeable batteries if the lock signals that their charge is insufficient for a few consecutive days. If insufficient charge is signaled occasionally, 
this does not mean that they have to be replaced: they may not have been sufficiently recharged after a power failure or very frequent use of the 
lock. In this case, recharge the batteries for at least 8 hours and use the lock electrically as little as possible, then check the charge level as described 
in paragraph 9.1.
In both cases, all of the batteries must be replaced at the same time, with new ones of the same brand and model. When replacing the 6 batteries, 
be extremely careful to respect their polarity in order to avoid permanent damage.
The battery pack is available in two versions: double tube or cassette.

ATTENTION: Drained batteries are harmful to the environment!!
They must be disposed of in special containers found wherever batteries are sold, as required by law.

Summary of Contents for Xmode F1.0





















Reviews: