background image

 

20

2.10 How to Replace the PEDAL SHAFT 

1) Disassemble the plastic 

PEDAL BASE. See “2.7.1 How to 

Disassemble PEDAL BASE” 

2) Loosen the upper PEDAL 

SHAFT (52) and the upper HEX 

LOCK NUT (13) 

a little

 by using 

17 mm spanner and 19 mm 

spanner each. Slight loosening 

through this process makes it 

easy to remove lower PEDAL 

SHAFT (52) securing the PEDAL 

COUPLER (58) to the PEDAL 

FRAME. 

3) Remove the lower PEDAL SHAFT (52) and the lower HEX LOCK NUT (13) by using 17 mm 

spanner and 19 mm spanner each. Two PEDAL REAR SHAFT BUSHes (62) are also removed. 

4) Remove the upper PEDAL SHAFT (52) and the upper HEX LOCK NUT (13) by using 17 mm 

spanner and 19 mm spanner each. 

5) Install new PEDAL SHAFT (52) in reverse order. 

 

2.11 How to Replace the HANDLE CRANK FRAME 

 

1) Remove SNAP RING (61) by using snap ring 

pliers. 

2) Remove the PEDAL FRONT SHAFT (59) 

from the HANDLE CRANK FRAME (94). PEDAL 

FRONT SHAFT BUSH (60) is also removed. 

3) Remove the COUPLER FRONT SHAFT (43) 

from the HANDLE CRANK FRAME (94). Be 

careful the COUPLER FRAME (42) can be 

fallen out of the HANDLE CRANK FRAME (94). 

4) Remove HANDLE BAR-L (107) by loosening 

four ALLEN BUTTON BOLTs (108) using 6 mm 

Wrench. 

5) Disconnect the interconnected Heart Rate Cable(C) under HANDLE BAR-L (107).   

6) Remove SNAP RING (98) by using snap ring pliers. 

Summary of Contents for M770E






































































Reviews: