9: CHOPPER HEAD
ACCESSORIES USED:
Reducer (l) and chopper head (m)
(depending on model).
ASSEMBLING THE ACCESSORIES:
9.1 Placing the reducer on the food pro-
cessor
- Place the reducer (l) on the motor unit
(a) by setting the marks of the reducer
and the motor unit (a) opposite one
another. Lock it by turning to the right.
9.2 Assembly of the chopper head
- Take the body (m3) by the feeder
tube, placing the widest opening
upwards. Then insert the screw (m5)
(long axis first) in the body (m3).
- Insert the knife (m6) on the short axis
placing the sharp edges outwards.
- Place the grid chosen (m7-1 or m7-2)
on the knife by aligning the lugs with
the notches in the head (m3).
- Tighten the nut (M8) on the body (m3)
clockwise, without blocking it.
- Check that everything is assembled.
The axis should not be able to wobble,
nor should it be able to turn round.
Otherwise, repeat the previous
operations.
- Clip the food guide (m4) under the
chopper head (m3).
9.3 Placing the chopper head on the
appliance
- With the appliance off and
unplugged, place the chopper head
(m) with the feeder tube tilted to the
right opposite the reducer. Fit the
chopper head firmly in to the reducer
(l).
- Bring the feeder tube back to the
vertical until it blocks. The chopper
head (m) will automatically lock on
the reducer (l) when it starts up
- Fit the removable tray (m2) on the
feeder tube.
- Plug the device in.
START-UP AND ADVICE:
- Prepare the amount of food to be
chopped. Remove the bones,
cartilage and nerves.
- Cut the meat into pieces (around 2 x
2 cm) and place them on the tray
(m2).
Place a receptacle under the chop
per head with the food guide (m4).
- Turn the speed switch (a3) to the
position "1" or "2" to start it up.
- Introduce the meat into the feeder
tube, piece by piece, using the pusher
(m1).
- Never push food with your fingers or
any other utensil.
Do not use your appliance for more
than 15 minutes when chopping meat.
- Make sure your meat is fully thawed.
10: STORAGE of the ACCESSORIES
Your food processor is equipped with a
storage box (o) can be positioned
inside the bowl (b). You can use it to
store the drive (c), the stainless steel
chopping knife (d), kneading knife (e),
2 disks: vegetable cutter (h) or
emulsifying disk (f)
11: CORD LENGTH ADJUSTMENT
For more comfortable use or easy
storage, you can reduce the length of
the power cord by pushing it inside the
motor unit (a) through the opening at
the back (a4).
33
- Unplug the device.
- For easier cleaning, rinse the
accessories quickly after use.
- Wash and dry the accessories: they
can all go in the dishwasher, in water
or under the tap with the exception of
the chopper head unit
(l+m3+m6+m7+m8) and the motor unit
(a). These should be wiped with a
damp sponge.
- Once dried, coat the 4 branch knife
(m6) and grids (m7) with edible oil to
prevent oxidation.
Robot notice 3:ROBOR BAGUIO 22/09/10 8:52 Page 33
Summary of Contents for FP518GB1/700
