These instructions are for the
Carseat Clip
that fits “
Discovery™
” and
“
SecureRide™
” infant car seats made by even
f
lo
®
,
only
.
This
Carseat Clip
fits the following model strollers:
IMPORTANT, KEEP FOR FUTURE REFERENCE
SCCEis1/4/04gen
2. Stroller Seat
WARNING
• Check you have correct Carseat Clip for
your car seat.
•
Do not use this Carseat Clip until you have
read and understood the instructions!
• Never leave your child unattended.
• Do not use accessories not designed for your
stroller as they may be unsafe.
• Do not leave baby in car seat (on or off
stroller) for long periods of time.
The seat can be fully removed from stroller before fitting Carseat Clip
(see instructions in stroller Instruction Booklet) or if more convenient,
seat can remain on stroller with partial unfastening.
3. Partial Seat Unfastening
1
2
3
Unfasten two middle fasteners on both sides of stroller and peel
fabric back, exposing frame.
For Urban model only, loosen the strap underneath seat at point
A
.
Recline seat slightly.
STAGE 1
Pull sunhood support wire out of sunhood joint
A.
This operation is
child proof and therefore requires a degree of force. To assist in pulling
sunhood support wire out, push against stroller frame with other hand
B.
Repeat step (1) on other side.
Unfasten sunhood fabric from stroller frame and seat near handle bar.
3
1
1. Removing Sunhood
(both models)
2
A
B
Sunhood Joint
The Sunhood needs to be removed from stroller before fitting
Carseat Clip
. NB: It can be replaced after
Carseat Clip
has been
fitted.
URBAN SINGLE - U1204
TERRAIN SINGLE - T1204
A
®
CARSEAT CLIP INSTRUCTIONS
Discovery™ & SecureRide™
B
C
These instructions are for the
Carseat Clip
that fits “
Discovery™
” and
“
SecureRide™
” infant car seats made by even
f
lo
®
,
only
.
This
Carseat Clip
fits the following model strollers:
IMPORTANT, KEEP FOR FUTURE REFERENCE
SCCEis1/4/04gen
2. Stroller Seat
WARNING
• Check you have correct Carseat Clip for
your car seat.
•
Do not use this Carseat Clip until you have
read and understood the instructions!
• Never leave your child unattended.
• Do not use accessories not designed for your
stroller as they may be unsafe.
• Do not leave baby in car seat (on or off
stroller) for long periods of time.
The seat can be fully removed from stroller before fitting Carseat Clip
(see instructions in stroller Instruction Booklet) or if more convenient,
seat can remain on stroller with partial unfastening.
3. Partial Seat Unfastening
1
2
3
Unfasten two middle fasteners on both sides of stroller and peel
fabric back, exposing frame.
For Urban model only, loosen the strap underneath seat at point
A
.
Recline seat slightly.
STAGE 1
Pull sunhood support wire out of sunhood joint
A.
This operation is
child proof and therefore requires a degree of force. To assist in pulling
sunhood support wire out, push against stroller frame with other hand
B.
Repeat step (1) on other side.
Unfasten sunhood fabric from stroller frame and seat near handle bar.
3
1
1. Removing Sunhood
(both models)
2
A
B
Sunhood Joint
The Sunhood needs to be removed from stroller before fitting
Carseat Clip
. NB: It can be replaced after
Carseat Clip
has been
fitted.
URBAN SINGLE - U1204
TERRAIN SINGLE - T1204
A
®
CARSEAT CLIP INSTRUCTIONS
Discovery™ & SecureRide™
B
C
