Moxa Technologies EtherDevice EDS-518A Series Hardware Installation Manual Download

Page: 17 / 17

- 17 -

Humidity

Regulatory Approvals

Safety

UL 60950-1, UL 508
CSA C22.2 No. 60950-1, EN 60950-1

Hazardous Location

UL/cUL Class I, Division 2, Groups A, B, C, and
D, ATEX Zone 2, Ex nA nC IIC T4 Gc

EMI

FCC Part 15, CISPR (EN 55022) class A

EMS

EN 61000-4-2 (ESD), Level 2
EN 61000-4-3 (RS), Level 3
EN 61000-4-4 (EFT), Level 2
EN 61000-4-5 (Surge), Level 3
EN 61000-4-6 (CS), Level 3
EN 61000-4-8
EN 61000-4-11
EN 61000-4-12

Shock

IEC 60068-2-27

Freefall

IEC 60068-2-32

Vibration

IEC 60068-2-6

WARRANTY

5 years

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:
Toll-free: 1-888-669-2872
Tel: 1-714-528-6777
Fax: 1-714-528-6778

Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel: +86-21-5258-9955
Fax: +86-21-5258-5505

Moxa Europe:
Tel: +49-89-3 70 03 99-0
Fax: +49-89-3 70 03 99-99

Moxa Asia-Pacific:
Tel: +886-2-8919-1230
Fax: +886-2-8919-1231

Summary of Contents for EtherDevice EDS-518A Series

















Search results

Summary of Contents for EtherDevice EDS-518A Series

Reviews:

Related manuals for EtherDevice EDS-518A Series

Brands by name

Popular brands

Moxa Technologies EtherDevice EDS-518A Series, Hardware Installation Manual

Search results

Summary of Contents for EtherDevice EDS-518A Series

Reviews:

Related manuals for EtherDevice EDS-518A Series

Brands by name

Popular brands