background image

 

WAPN008-1 User’s Manual 

The hardware and software described in this manual is furnished under a license agreement and may be used 

only in accordance with the terms of that agreement. 

 
 

Copyright Notice 

 

Copyright 

 2019 Moxa Inc. 

All rights reserved. 

Reproduction without permission is prohibited. 

 
 

Trademarks 

 

MOXA is a registered trademark of Moxa Inc. 

All other trademarks or registered marks in this manual belong to their respective manufacturers. 

 

Disclaimer 

 
Information in this document is subject to change without notice and does not represent a commitment on the 
part of Moxa.

 

Moxa provides this document “as is,” without warranty of any kind, either expressed or implied, including, but 
not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this 
manual, or to the products and/or the programs described in this manual, at any time. 

Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no 
responsibility for its use, or for any infringements on the rights of third parties that may result from its use. 

This product might include unintentional technical or typographical errors. Changes are periodically made to 
the information herein to correct such errors, and these changes are incorporated into new editions of the 
publication. 

Technical Support Contact Information 

www.moxa.com/support 

 

Moxa Americas: 
Toll-free: 1-888-669-2872 
Tel: 

+1-714-528-6777 

Fax: 

+1-714-528-6778 

Moxa China (Shanghai office): 
Toll-free: 800-820-5036 
Tel: 

+86-21-5258-9955 

Fax: 

+86-10-6872-3958 

Moxa Europe: 
Tel: 

+49-89-3 70 03 99-0 

Fax: 

+49-89-3 70 03 99-99 

Moxa Asia-Pacific: 
Tel: 

+886-2-8919-1230 

Fax: 

+886-2-8919-1231 

 

 

 

Summary of Contents for WAPN008-1














Reviews: