2. Apply rust inhibitor to all unpainted cast iron and
machined carbon steel surfaces.
3. Remove drive belts if applicable.
4-54. PACKING SPECIFICATION
Standard packing on all Moyno 2000 pumps consists of
braided PTFE fibers impregnated with ultrafine graphite.
Optional types of packing are available for food, high tem-
perature and other types of service. Consult your nearest
Moyno representative.
4-55. VARIATIONS OF STANDARD PARTS
Below are variations available for modifying pumps to
meet specialized pumping conditions. If the trim code of your
pump is other than “AAA,” contact your nearest Moyno
representative for clarification. Do not modify your pump
with any variation unless you have determined that it is com-
patible with your application.
The three-character trim code is designed as follows.
The first character identifies any sealing variations, the sec-
ond character identifies any internal variations, and the third
character identities any rotor variations.
The trim code ‘AAA” represents a pump with standard
features. Deviations from standard are to be indicated by
changing the appropriate character from the choices listed.
When two or more letters are combined, dashes are used to
separate the three areas of the trim code for clarity.
SEALING VARIATIONS
A — BRAIDED TEFLON & GRAPHITE PACKING,
(Black) Standard to all lines except Quick
Disassembly pumps. Optional on Quick
Disassembly pumps.
C — BRAIDED TEFLON PACKING, (White) Optional
packing on all lines,
D — DOUBLE MECHANICAL SEAL, Optional on all
lines. Not offered on #2 “L” frame.
F —
BRAIDED TEFLON FOOD GRADE PACKING,
(White) Standard on all Quick Disassembly
pumps. Optional on all other lines.
G — 100% GRAPHITE PACKING, (Gray) Optional to
all lines.
H — FLUSH PACKING GLAND
S — SINGLE MECHANICAL SEAL, Optional on all
lines.
W — WATER FLUSH, Optional on all lines.
X — Special to application
Page 13
INTERNAL VARIATIONS
A — Standard plated shaft
B — Non-plated
shaft
C — Solid drive shaft configuration
D — Grit seal, for ‘L” frame only
E — Extension tube with extended auger
F — Extended drive shaft (for back stop or large pulley)
G — Ceramic coating
S — Shaft
sleeve
X — Special to application
ROTOR VARIATIONS
A — Standard size with chrome plating
B — Non-plated (no plating)
C — Standard
undersize
E — Standard
oversize
F — Counter clockwise rotation (Centennial line only)
G — Ceramic coating
X — Special to application
4-56. Rotors
identified on parts listing are standard size with
hard chrome plated surface. Other variations of rotor size
and finish may be ordered by selecting the standard rotor
part number and changing the last digit of the rotor number
as follows:
2 = Standard size, non-plated
3 = Undersize, chrome-plated
4 = Undersize, non-plated
5 = Oversize, chrome-plated
Do not change rotor sizes without consulting your local
Moyno Sales Office. These variations are used for certain
specialized pumping conditions only.
4-57. Drive Shafts
shown have hard-chrome plating on
the
packing wear area. If non-plated drive shafts are required,
select the standard part number and change the last digit to
next higher number; example: PE0261 to PE0262.
Summary of Contents for Version 3
