manualshive.com logo in svg

MQ BA-SERIES, Operation And Parts Manual

The MQ BA-SERIES is a must-have equipment for builders and contractors. Enhance your productivity with this sturdy and reliable machine. Maximize its potential by referring to the comprehensive Operation and Parts Manual. Download the manual for free from our website, where you can find a plethora of user manuals to cater to your needs.

Share
Download
background image

PAGE 34 — BA-SERIES  WALK-BEHIND TROWEL— PARTS & OPERATION MANUAL — REV. #3 (11/30/04)

Figure 48.  Hand Clutch Adjustment

11. Carefully lift 

the 

upper trowel assembly

, line up the key-

way on gear box main shaft and insert into spider assembly.

12. Reinstall square head cone point into spider plate and

tighten in place. Tighten jam nut. Use care in making sure
point of set screw engages groove in gear box main shaft.

13. Lubricate all grease points (zerk fittings) with premium

"

Lithum 12"

 based grease, conforming to NLG1 Grade #2

consistency.

Testing

1. Place trowel in test area, start engine and test trowel for

smoothness.

2. If trowel bounces has excessive vibration or does not run

smoothly repeat alignment procedure.

Changing a Blade

Whiteman recommends that

 all the blades be changed at the

same time

. The machine may wobble or bounce if only some of

the blades are changed at one time.

1. Place the machine on a flat, level surface. Adjust the blade

pitch control to make the blades as flat as possible. Note the
blade orientation on the trowel arm.

Before removing the blades, please note
the orientation of the blade on the trowel
arm.

NOTE

1. Remove the three bolts and lock washers that secure the

blade to the trowel arm. Remove the blade.

2. Using a wire brush, scrape all concrete particles  and foreign

debris from the trowel arm.

3. Install the new trowel blade onto the trowel arm. Make sure

blade is installed correctly, maintaining the proper orienta-
tion for direction of rotation

.

4.

Reinstall 

 the three bolts and lock washers that secure the

blade to the trowel arm. Tighten all three bolts securely.

5. Repeat steps 1-4 for all remaining blades.

BA-SERIES TROWEL — MAINTENANCE

Hand Clutch Adjustment

Some trowels  are  equipped with a hand-operated clutch instead
of an automatic centrifugal clutch. Two types of hand clutches
have been installed. Both are belt-tightener type clutches. They
operate by removing 

slack

 in the V-belt which then transmits

power from the engine to the gearbox.

There are two reasons to adjust the hand clutch: 1) operator
comfort; 2) initial belt stretch and break-in.

The easiest and most simple adjustment is to adjust the clutch
cable housing using the adjustment nut (Figure 48) located on the
clutch lever. Rotating the nut provides either more or less
(depending upon the direction of rotation) clutch engagement.

Hand Clutch Disengagement

1. Start the trowel as outlined in the "

Initial Start-up

" section in

this manual. Move the throttle lever so that the engine is
running about 1/4 to 1/3 of full speed.

2. Grip the trowel handle firmly and carefully engage the clutch

by squeezing the clutch lever toward the handle with your left
hand. After the trowel is stabilized and you feel comfortable
with its operation, use your right hand to adjust the housing
adjustment nut.

3.

Rotating the nut so that it backs out of the lever housing
increases the engagement and also the squeezing force
required to keep it engaged.

Too much squeezing force may cause premature hand
fatigue. Too little squeezing force may cause belt slippage
and premature belt wear. Each operator should experiment
with the adjustment to get the optimum combination of
squeeze force and belt grip.

4.

After initial break-in (approximately 8 hours) the above
procedure should be repeated to attain optimum operator
comfort and belt wear.

5.

After considerable belt wear, the adjustments mentioned
above may have a little or no effect on clutch engagement. If
this is the case, the belt should be replaced.

Summary of Contents for BA-SERIES







































Reviews:

No comments

Related manuals for BA-SERIES

MAKER MT36-4 Operating Instructions Manual preview
MT36-4
Brand: MAKER Pages: 21
BETON TROWER BT900 HPFH24.1 Instruction Manual preview
BT900 HPFH24.1
Brand: BETON TROWER Pages: 40
allen RAZORBACK RIDER HD560 Operations Manual And Parts Book preview
RAZORBACK RIDER HD560
Brand: allen Pages: 42

Brands by name

Popular brands

Load more brands