manualshive.com logo in svg

MQ BA-SERIES, Operation And Parts Manual

The MQ BA-SERIES is a must-have equipment for builders and contractors. Enhance your productivity with this sturdy and reliable machine. Maximize its potential by referring to the comprehensive Operation and Parts Manual. Download the manual for free from our website, where you can find a plethora of user manuals to cater to your needs.

Share
Download
background image

PAGE 8 — BA-SERIES  WALK-BEHIND TROWEL— PARTS & OPERATION MANUAL — REV. #3 (11/30/04)

BA-SERIES TROWEL—  SAFETY MESSAGE ALERT SYMBOLS

Safety precautions should be followed at all times when operating
this equipment.  Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

This Owner's Manual has been developed to provide
complete instructions for the safe and efficient operation
of the MultiQuip BA-SERIES WALK-BEHIND TROWEL.
For engine maintenance information, please refer to the
engine manufacturers instructions for data relative to its
safe operation.

Before using this WALK-BEHIND TROWEL, ensure
that the operating individual has read and
understands all instructions in this manual.

NOTE

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others.  The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words:  

DANGER

,

WARNING

, or 

CAUTION

.

DANGER: 

You 

WILL

 be 

KILLED

 or

SERIOUSLY injured if you 

DO NOT

 follow

directions.

WARNING: 

You 

CAN

 be 

KILLED

 or

SERIOUSLY injured if you 

DO NOT

 follow

directions.

CAUTION: 

You 

CAN

 be  injured if you

DO NOT

 follow directions.

HAZARD SYMBOLS

Engine exhaust gases contain poisonous

carbon monoxide.  This gas is colorless and

odorless, and can cause death if inhaled.

NEVER

 operate this equipment in a confined

area or enclosed structure that does not

provide ample free flow air.

Potential hazards associated with B-Series trowel operation will
be referenced with "

Hazard Symbols

" which appear throughout

this manual, and will be referenced in conjunction with Safety
"

Message Alert Symbols

".

Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited.  

DO

NOT

 start the engine near spilled fuel or

combustible fluids. 

 DO NOT

 fill the fuel tank

while the engine is running or hot.  

DO NOT

overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system.  Store fuel in
approved containers, in well-ventilated areas

and away from sparks and flames.  

NEVER

use fuel as a cleaning agent.

Burn Hazards

Engine components can generate extreme heat.
To prevent burns, 

DO NOT

 touch these areas

while the engine is running or immediately after
operations. 

 NEVER 

operate the engine with

heat shields or heat guards removed.

Rotating Parts

NEVER

 operate equipment with covers, or

guards removed.  Keep fingers,

 hands

, 

hair

 and

clothing

 away from all moving parts to prevent

injury.

Explosive Fuel

Lethal Exhaust Gases

Summary of Contents for BA-SERIES







































Reviews:

No comments

Related manuals for BA-SERIES

MBW 1780001 Operator'S Safety And Service Manual preview
1780001
Brand: MBW Pages: 21
WACKER Group 0007587 Repair Manual preview
0007587
Brand: WACKER Group Pages: 44
Wacker Neuson CRT48-35V Operator'S Manual preview
CRT48-35V
Brand: Wacker Neuson Pages: 116

Brands by name

Popular brands

Load more brands