IV-12 VFD Clock Jenny
IV-12 VFD Clock Jenny
Example: Time setup
Starting at
display mode
hold button SET for 2s.
Seconds starts to flash................................
1 4
1 4
1 4
1 4
1 4 5 6
5 6
5 6
5 6
5 6
Push SET (minutes are flashing)...................
1 4
1 4
1 4
1 4
1 4
1 6
1 6
1 6
1 6
1 6
Push button ADJUST several times and set
the correct minutes time .............................
1 4
1 4
1 4
1 4
1 4
2 4
2 4
2 4
2 4
2 4
Push button SET (hours are flashing) ............
0 0
0 0
0 0
0 0
0 0 3 2
3 2
3 2
3 2
3 2
Push button ADJUST several times and set
the correct hours time .................................
0 0
0 0
0 0
0 0
0 0 4 1
4 1
4 1
4 1
4 1
Push button SET (seconds are flashing) ........
1 6
1 6
1 6
1 6
1 6 0 0
0 0
0 0
0 0
0 0
Push button ADJUST ...................................
1 6
1 6
1 6
1 6
1 6 0 0
0 0
0 0
0 0
0 0
Every time when pushing the button ADJUST the seconds
are set to „00“. Repeat this step until the correct time is
valid.
Now hold button SET for 2s to exit
setup mode
. The clock
returns to the standard
display mode
.
Example: Alarm setup
Starting at
display mode
push button MODE once to
display the alarm time, then hold button SET for 2s.
Hours starts to flash ...................................
00
00
00
00
00
1
1
1
1
1
Push button ADJUST several times and set
the correct hour for the alarm ......................
00
00
00
00
00
1
1
1
1
1
Push button SET (minutes are flashing) ........
06
06
06
06
06
1
1
1
1
1
Push button ADJUST several times and set
the correct minutes for the alarm .................
06
06
06
06
06
1
1
1
1
1
Push button SET (seconds are flashing) ........
06
06
06
06
06 15
15
15
15
15
Push button ADJUST several times ...............
06
06
06
06
06 15
15
15
15
15
Pushing ADJUST sets the snooze delay between 1 and 9
minutes.
Now hold button SET for 2s to exit
setup mode
. The clock
returns to the standard
display mode
.
10
3
For your safety – please read carefully!
•
Don’t open the enclosure when the clock is
powered up. There are no serviceable parts inside.
•
Danger! High voltage exists on the board. Do not
touch parts of the circuit during testing other than
the switches while the clock is under power.
•
Do not operate the clock with damaged or
removed tubes.
•
Handle the clock with care.
•
Beware of hard impacts.
•
Use the clock only in a dry environment.
•
Don’t expose the clock to moisture or rain.
•
The clock warms up during operation. Don’t
operate near heat sources or cover the clock.
•
Don’t place or use the clock on metal surfaces.
•
Only replace the AC power adapter with one
with similar ratings as stated in the technical
data sheet.
Starting up
Simply plug in the DC connector of the supplied wall power
supply to the 12V= jack on rear and plug the power supply
to your wall socket.
The clock is powered up and shows the time
0
0
0
0
0 00
00
00
00
00 00
00
00
00
00
.
Three different modes
Three different modes are used to maintain the clock, the
buttons MODE and SET toggles between these modes:
•
display mode
(mode for display time / date)
•
setup mode
(to setup the clock)
•
option mode
(for customizing your clock)
If no buttons are pressed for several seconds while
within either
setup mode
or
option mode
the clock
will automatically exit to the standard
display mode
.
