background image

8701 Castle Park Drive 

 Indianapolis, Indiana 46256

Telephone: (317) 842-2545 

 www.mssedco.com 

 custsvc@mssedco.com

216, 216-L, 216-N

Active Infrared "Touchless" Switch 

INSTALLATION INSTRUCTIONS

Page 2

(82A023)  216v1014

Section 3

Technical Data

Model....................................... 216, 216-L, 216-N

Input Power.............................. 12-24V AC or DC

Input Current............................ Approx. 100 MA @ 18V AC

Output Connections................. 8" 22 AWG Leads

Output Rating........................... Form C, Rated at 3 Amps

Detection Scheme................... Coded Modulated Carrier

Codes Available....................... Automatic Self Changing ID 

 

Coding

Activation Time........................ <0.03 seconds

Reaction Time.......................... 0.05 - 1 second

Operating Distance.................. 6" to 30"

Temperature Rating................ -13°F to 140°F 

 

(-25°C to 60°C)

Weight...................................... <0.25 lbs.

Physical Size............................ 1 5/16"L x 4"W x 1 1/4"H

Section 4

Warranty

MS SEDCO guarantees this product to be free from manufacturing 

defects for 1 year from date of installation.  Unless MS SEDCO is 

notified of the date of installation, the warranty will be in effect for 

1 year from the date of shipment from our factory.  If, during the 

first  year,  our  motion  detector  or  support  device  fails  to  operate 

and  has  not  been  tampered  with  our  abused,  the  unit  can  be 

returned prepaid to factory and it will be repaired free of charge.  

After 1 year, the unit will be repaired for a nominal service charge.  

This limited warranty is in lieu of all other warranties expressed 

or  implied,  including  any  implied  warranty  of  merchantability, 

and no representative or person is authorized to assume for MS 

SEDCO  any  other  liability  in  connection  with  the  sale  of  our 

products.    All  warranties  are  limited  to  the  duration  of  this 

written warranty.  In no event shall MS SEDCO be liable for any 

special,  incidental,  consequential  or  other  damages  arising 

from  any  claimed  breach  of  warranty  as  to  its  products  or 

services.

Questions?  Call us at 1-317-842-2545 or

visit us online at www.mssedco.com.

Summary of Contents for 216

Page 1: ... and the foam gasket on the front of the switch assembly are less than 1 4 apart Figure 4 2 GANG ELECTRICAL BOX OR JUNCTION BOX 216 1 Install the electrical box purchased separately in its intended location 2 Attach the adaptor ring provided see below to the electrical box 3 Set the unit for its intended operating mode via the jumpers on the side of the switch assembly Fail Close factory setting F...

Page 2: ...on Unless MS SEDCO is notified of the date of installation the warranty will be in effect for 1 year from the date of shipment from our factory If during the first year our motion detector or support device fails to operate and has not been tampered with our abused the unit can be returned prepaid to factory and it will be repaired free of charge After 1 year the unit will be repaired for a nomina...

Page 3: ...ctivated again returning the relay to its de energized state For example a 216 series switch could be located at the entrance of a room When a person enters the 216 series switch turns on the light As they exit the 216 series switch turns off the light In order to program this mode cut Jumper 2 Wire connections are COM and N O Input Connections Output Connections 12 24V AC or DC Green Common COM R...

Page 4: ...e lens and foam gasket should be touching WARNING When attaching the face plate to the switch assembly only use 6 32 x 3 8 screws provided Use of longer screws may cause damage to the unit Range Adjustment Clockwise to increase 6 to 30 NOTE When attaching the face plate the range may increase Reaction Time Adjustment Clockwise to increase 0 05 to 1 second SIDE VIEW REACTION TIME 0 05 1 Sec INC RAN...

Reviews: