background image

REMOVING THE RESPIRATOR

DECONTAMINATION

DO NOT remove respirator until respirator and protec-
tive clothing are decontaminated; otherwise, exposure
to contaminants may result. Follow decontamination
and disposal procedures established by appropriate
authorities. Failure to follow this warning may result in
serious personal injury or death.

Once the protective equipment has been decontaminated,
proper disposal of affected equipment must be per-
formed.

Disposal is to be performed as required by federal, state,
and/or local laws.

When conditions are safe to remove and handle the respi-
rator, the switch can be moved to the “OFF” position, and
accessories/components (belt, canisters etc) can be
removed. Refer to the facepiece user’s instruction manual.

DO NOT reuse the canisters. Canisters are considered
to be in service when they are removed from their
packaging. Canisters are intended for one time use
only and must be disposed of upon termination of use.

1. Open the battery compartment by unthreading

(counter-clockwise) the battery cap assembly.

2. Remove the battery.

a. The non-rechargeable LI-SO2 battery must be dis-

posed of on termination of use. Do not reuse the
battery.

b. The rechargeable NiMH battery can be recharged

according to the instructions on the battery label
and in the Charging the C420 Rechargeable Battery
section of this user’s instruction.

The rechargeable battery can only be charged using
the MSA battery charger. Failure to follow this warning
can result in serious personal injury or death. DO NOT
dispose of batteries as ordinary trash. Follow the
instructions included in the Disposal of Canisters and
Batteries section.

3. Clean, inspect, and prepare the C420 PAPR for the

next use.

15

TAL 804 (L) Rev. 0 - 10086003

Summary of Contents for FireHawk M7 Responder PAPR

























Reviews: