background image

TAL 0110 (L) Rev. 8 - 10020949

TEST METHOD FOR OPTIMAIR MM 2K

Resistance" will result in an indication
of charge failure status by the charger.
In this case, the battery pack is defec-
tive and should be replaced.

Indication of charge failure status when
attempting to charge a battery which
passes these tests is an indication of
charger failure and the charger must be
replaced.

TESTING THE MOTOR-BLOWER:

The function of the motor-blower can
be tested by using an MSA flowmeter
and a multimeter. (An MSA wall mount-
ed Flow Tester p/n 488903 or the
adapter p/n 491046 and 487995 is
required to run the flow test)

Before Testing:

1. Examine the motor-blower for

cracks or other physical damage. If
any of these conditions exists,
replace the battery pack.

2. Using a good battery pack as deter-

mined by the previous tests, fully
charge the battery until a full charge
is achieved.

Testing the Flow of the motor-

blower:

1. Assemble the motor-blower to the

battery pack.

2. Attach the motor-blower to the flow

meter per the supplied instructions.

3. Turn on the MM 2K and notice the

volumetric flow.

4. This flow must be above 115 lpm.

Testing the Resistance of the

Motor:

1. Refer to Diagram 1 for proper pin

locations.

2. Set the multimeter to measure

resistance.

3. Place the positive probe on pin 1

and the negative probe on pin 2.

4. The resistance should be less than

10W.

25

Quick Reference Chart – Battery Tests

Test

Multimeter

Positive

Negative

Switch

Value

Setting

Probe

Probe

Setting

Open Circuit Voltage

Voltage

Pin 1

Pin 2

Off/On

0 / >4.8 Volts

Switch Circuit

Open Circuit Voltage

Voltage

Pin 4

Pin 2

On or Off

> 4.8 Volts

Recharge Circuit

Thermistor Resistance

Resistance

Pin 3

Pin 2

On or Off

7K

–18K

Charger Control

Circuit

D

E

Summary of Contents for OptimAir MM 2K

































Reviews: