background image

12

Make sure all water is drained from the spa tub and the control box. This is essential to extend the life of the spa. 
You could also use a vacuum or hair blower to suck up or blow out the water from the pipe and pump lines. Filter 
cartridge also needs to be removed. It is recommended to store the spa tub in the original packaging box. Store the 
tub in a warm and dry place.

NOTE: 

Make sure all components are completely dry and clean before packaging. Store the spa tub safely in a 

warm and dry condition. Exposure to sunshine is not recommended. Plastic can becomes brittle and susceptible to 
breakage when exposed to a sub-zero temperature environment. Icy weather or store below sub-zero temperature 
can severely damage the spa tub. Improper winterization of your MSpa may void your warranty.

Spa checklist before unpack the unit and re-use for the new season:

In order to have your MSpa runs smoothly and easily for another new season, make sure you do the follow:
1. Check if there is water in the air pipe. If any water is found, dry the air pipe before operating the spa tub.
2. Connect control panel correctly, turn on the spa tub, check if LED displays correctly and if the signal cable is 
    connected properly.
3. Press ON / OFF button on the control panel, open bubble function, check if it operates properly.
4. After doing the above steps, your MSpa should be ready for use. Enjoy it!

Any damage caused by improper storage or failure to do the checklist of reuse will void your warranty.

DISPOSAL

1.The marking               indicates that this product shall not be disposed with the general household waste.
   Please contact your local community about collection points or ask your dealer.
2.This product contains valuable materials that can be recycled and contributed to a sustainable environment.
3.For recovery, recycling and dismantling information for this product, please visit us at
   

www. the-mspa. com

TROUBLESHOOTING

Mspa® strives to provide the most trouble-free spas on the market. If you experience any product related problems, 
do not hesitate to contact us or your local after sales service center.
Here are some helpful tips to help you to diagnose and rectify some common sources of trouble.

* For any spare parts you need for replacement, please refer to the warranty policy for replacing details.
* For any other unknown failures out of the list, please contact your national or regional MSpa service center.

Summary of Contents for B- 131 Luxury Exotic


















Reviews: