background image

 

 

2019  Premium  Concept  Elite  Service  Manual 

 

Visit our website at: www.the-mspa.com

 

                                                                                                                         

 

- 26 - 

 

   

 

 

3

Loosen five screws (ST4*15) from the rear cover

 

of  the  cabinet;  Loosen  two  screws  (ST4*15)  from  the 
base of the cabinet   

4

Take out the internal cabinet and power board

 

     

 

   

 

6

 Loosen three screws from the junction box; Loosen 

4 black insertion pins 

6、

Remove 4 screws and open the power board; cut off 

the bindings and take out the 2 lead wires of

 O3; 

 

 

7、

Remove the connection strap of the O3 joint pipe 

and the one-way valve with inclined tongs, and remove 

the O3 joint pipe

 

8、

With the cross screwdriver, remove the 4 screws that 

fix O3 and remove the O3 generator (pay attention to 

the wire and hole of O3 pipe when removing, do not 

reverse it).

 

9、

Assemble the new O3 generator in reverse order

Make sure the O3 connection pipe and power cord are 

through the correct base hole, not inverted

 

 

4.10 How to Replace Jet element 

 

 

1. Use wrench to screw these 3 outlets/inlet 

2. 

Unscrew the screws of the air valve.

; 

Summary of Contents for Concept 2019









































Reviews: