background image

 

 

2019  Premium  Concept  Elite  Service  Manual 

 

Visit our website at: www.the-mspa.com

 

                                                                                                                         

 

- 35 - 

 

Question: 

Answer:  If the spa is filled with 80% of its maximum water capacity, the depth is about 44-46cm.   

29:     

Question: 

What is the steepest slope that I am able to set up my spa on? 

Answer:  For  best  results,  the  surface  should  be  perfect

ly  level. Pay close attention to the spa’s stability and 

levelness  in  the  early  stages  of  filling  your  spa  up  with  water.  If  after  about  an  inch  of  water  is 
accumulated, and the water is not spreading out evenly, or the spa appears to be bulging to one side, 
stop filling the spa, drain the water, and select a new site. If the spa is set up on a slope, the spa will be 
lopsided and could collapse. 

Never set up the spa on slope ground. 

30:     

Question: 

What material is the spa made of? 

Answer:  The spa pool is mainly made with a heavy gauge of PVC. 

31:     

Question: 

What other surfaces can be safely used to set up my spa? 

Answer:  The  spa  can  be  set up  on  grass  or  pavement  that  is  completely  smooth,  level  and  stable.  A  ground 

cloth  or  tarp  is  recommended. The  spa  should  NOT  be  set up  on  sand  or  muddy  ground  that  could 
possibly shift around.   

32:     

Question: 

What should the customer use to clean his spa before storing it for the winter? 

Answer:  The customer can use mild soap and  water to  clean  his spa. He shall clean the spa thoroughly  and 

make sure the spa is completely dry before storing. Please refer to Q 44. 

33:     

Question: 

Why  sometimes  can  algae  be  found  in  the  spa  even  the  customer  runs  the  filter  pump 
regularly? 

Answer:  The filter  pump itself  will  not prevent algae from growing in the spa  water; this can  only  be done by 

maintaining proper chlorine and pH levels at all times. The customer can check the local pool chemical 
supplies store for further information. 

34:     

Question: 

Would excessive spa chemicals affect / cause deterioration to the spa pool(liner)? 

Answer:  Excessive or concentrated chemicals may cause damage to the spa liner and the user.   

35:     

Question: 

Why an extension cord should not be used as stated in the spa set up instruction? 

Answer: 

In order to reduce the risk of electric shock, the customer can’t cut off the cord and connect the cord 
with  another  one  to  extend  the  length  of  the  power  supply  cord  by  himself  since  this  may  cause 
potential  danger.  It  is  important  only  to  use  a  10A  power  supply.  If  the  customer  has  to  use  an 
extension cord/connecting cable, please make sure this is for 10A purpose and for outdoor use. For 
safety reasons, set up spa a few meters away from power supply.   

36:     

Question: 

When the setting temperature is lower than the environment or water temperature, is the heater 
will be defective as the heater button does not light up? 

Answer:  No. 

37:     

Question: 

Why does the bubbling stop working suddenly? 

Answer:  It is normal. As our spa is designed to have an automatic stop of the bubbling function.   

Summary of Contents for Concept 2019









































Reviews: