LED display
Once powered-up, press the
RESET
on the PRCD. The LED displays the current water temperature automatically.
NOTE:
The actual water temperature may vary from the temperature displayed on the LED screen by as much as approximately 1°C.
UVC SANITIZER
Press the UVC button to turn the UVC sanitizing system on/off. When the light above this button is green, the UVC sanitizing system is
activated.
HEATING
1. Press the
HEATER
button to turn the heating system on/off. When the light above the heat button is red, the heating system is activated.
When the light is green, the water is at the set temperature and the heating system is at rest.
2. Pressing the
UP
or
DOWN
button will cause the LED to flash. When it is flashing you can adjust the water to the desired tempera
ture setting (from 20°C to 40°C ). The new and desired temperature setting will remain on the LED display for 3 seconds to confirm the new value.
NOTE:
The default temperature is 38°C.
NOTE:
If the heating system is turned on, the filtration system will automatically start.
NOTE:
When the water temperature is below 1°C (33.8°F), the anti-icing system will be activated automatically to heat the water to 3°C (37.4°F).
IMPORTANT:
The following conditions will lead to slow water heating
An ambient temperature lower than 10°C (50°F).
An outdoor wind speed above 3.5-5.4m/s (8-12mph).
If the air bubble function is activated when the heater is on.
If the spa cover is not properly in place when the heater is on.
FILTRATION
Press the
FILTER
button to turn the function on/off. The light turns to green when the function is activated.
NOTE:
The filtration system will automatically start when the heating or UVC sanitizing system is activated.
NOTE:
After turning off the heating system, the filtration system will automatically stop in 30 seconds.
Filter Cartridge Cleaning Reminder:
When the FILTER button is flashing or displays red, the filter cartridge must be cleaned or replaced. Once
this has been done, press the Filter button for 3 seconds to reset the reminder.
BUBBLE MASSAGE
Press the
BUBBLE
button to turn the massage system on/off. The Bubble button displays green when activated.
IMPORTANT:
Do not turn on the massage system when the cover is attached. Air can accumulate inside the spa and cause irreparable damage
and bodily harm.
NOTE:
The bubbling massage function will shut down automatically after every 20 minutes of operation as a safety precaution. This can be
reactivated after 10 minutes by pressing the BUBBLE button again.
HEATING TIMER
To set the number of hours
FROM NOW
when the heater will activate:
1. Press the
TIMER
button to enter pre-setting mode. The button displays green.
2. Pressing the
UP
or
DOWN
button will cause the LED to flash. While it is flashing, you can adjust the number of hours before heater
activation (from 1 to 99 hours). The desired timer setting will remain on the LED display for 3 seconds to confirm the value.
To modify the timer setting:
Press the
Timer
button again and use the
UP
or the
DOWN
button to adjust.
Cancel the setting:
Press the
TIMER
button for 3 seconds.
NOTE:
Activating the heating system or rebooting the spa will cancel the timer setting.
SAFETY LOCK
Press the
UP
and
DOWN
buttons at the same time for 3 seconds to lock/unlock the controller. In safety lock mode, the controller is
disabled and the spa retains all previous settings.
Celsius/Fahrenheit Toggle Button
The temperature can be displayed in either Celsius or Fahrenheit. Long press
DOWN
button for 3 seconds to switch.
FILTER
FILTER
HEATER
HEATER
BUBBLE
UP
DOWN
TIMER
11
UVC
UVC
UP
DOWN
UP
DOWN
DOWN
20-40
°C
1-99H
TIMER
BUBBLE
●
●
●
●
3s
UP
DOWN
3s
DOWN
+
°C
°F
