background image

18

WATER MAINTAINCE AND CHEMICALS

Water Sanitation

The spa owner must regularly check and keep the spa water sanitized with scheduled maintenance (daily, if 

necessary). Adding sanitizer or other chemical will control bacteria and viruses present in the spa water. The 

maintenance of a proper water balance through appropriate use of sanitizers is the most important factor in 

maximizing the life and appearance of the spa as well as ensuring clean, healthy and safe water. 

Proper technique is important for water testing and treating the spa water. See your spa professional for 

chemical, sanitizer, test kit and testing procedures questions. 

CAUTION: 

●   

Always follow the chemical manufacturer’s direction, and the health and hazard warning. 

●   

Do not add chemicals if the spa is occupied. This can cause skin or eye irritation. 

●   

Concentrated chlorine solutions can damage the spa tub. Improper chemical use will void the warranty.

Maintenance of Spa Water and Cartridge

Protect all the spa occupants from possible water related illness by keeping the spa water clean and sanitized. 

Always practice good hygiene. To ensure proper spa water quality by following these procedures:

1.   Inspect and clean the filter cartridge after each use, and change the filter cartridge after it works 

continuously for 72 hours. 

●   

Unscrew the cartridge assembly from the spa tub wall and remove the cartridge by turning it 

counter clockwise (Fig. 1.1)

●   

Use a garden hose to rinse off the cartridge. If the cartridge remains soiled and discolored it should be 

replaced. Keep spare cartridges on hand.(Fig.1.2). 

There are two filter cartridges from the original 

package, one is for use, one is spare.

 

●   

Reinstall the clean or spare cartridge back onto the spa tub wall but turning it on clockwise. (Fig.1.3)

1.1

1.2

1.3

2.   Change the spa water every 3-5 days depends on the spa use. See “Cleaning, draining and storage” 

section for instruction.

3.   Use spa chemicals to maintain proper water chemistry. Spa damage resulting from misuse of chemicals 

and mismanagement of spa water is not covered by the warranty. Consult with your local spa or pool 

retailer for more information on chemical use. 

4.   All occupants must shower before entering the spa.
5.   When spa inlet or outlet is stuck with dirt. Use the

Wrench to check the problem and clean the inlet 

or outlet. 

5

Summary of Contents for PM-610S Tuscany

























Reviews: