MTD 19B70004OEM Operator'S Manual Download

Page: 15 / 20

ection

4 — A

SSembly

& i

nStAllAtion

Install The Counter Weight

The front weight kit is designed for use with all RZT-L (Lap

Bar) Residential Zero-turn models. The front weight kit is

NOT

designed nor required for use with all RZT-S (Steering Wheel)

Residential Zero-turn models.

WARNING:

This front-weight kit is required when

operating any compatible lap bar RZT-L models

equipped with a grass collector. Failure to install this

kit may result in serious injury or death.

WARNING:

Before beginning installation, place

the RZT-L on a firm and level surface, set the parking

brake, place the PTO in the disengaged (OFF)

position, stop the motor and remove the ignition

key to prevent unintended starting.

Note:

The front weight kit is not utilized on the RZT-S (Steering

Wheel) Residential Zero Turn units. Do not attempt to mount it

on RZT-S models, as it will not fit.
RZT models are available with two different front-end styles.

Identify your RZT using the images in the following instructions

and follow the applicable steps.

RZT Models with a Pivoting Front Axle

Note:

Having a second person assist you by holding the weight

bar in place will ease in completing the following steps.
1.

Insert the two 3 1⁄4-inch (710-3056) screws from hardware

pack 689-00325, into the weight bar.

Position the weight bar onto the foot rest and secure it in

place with two 3⁄8” flange nuts (712-04065) from the same

hardware pack. See Figure 4-25.

Note:

To hold and retain nut for tightening, it may

be necessary to insert the nut into the box end of a

combination wrench and slide up through the opening in

the floorboard.

Figure 4-25

RZT Models with a Fixed Front Axle

Attach the left mounting bracket and the right mounting

bracket to the weight bar using two 21⁄2-inch screws (710-

0859), and 3⁄8” flange nuts (712-04065) from hardware pack

689-00325. See Figure 4-26.

Figure 4-26

Attach the weight bar assembly to the front axle with a 3

1⁄4-inch (710-3056) screw and (712-04063) flange nut from

hardware pack 689-00325 on the left side. Repeat on the

right side. Do not fully tighten at this time. See Figure 4-27.

Figure 4-27

Visually center the weight bar assembly on the tractor

and tighten the hardware installed in step 2 to secure the

brackets to the front axle.

Summary of Contents for 19B70004OEM





















Search results

Summary of Contents for 19B70004OEM

Reviews:

Related manuals for 19B70004OEM

Brands by name

Popular brands

MTD 19B70004OEM, Operator'S Manual

Search results

Summary of Contents for 19B70004OEM

Reviews:

Related manuals for 19B70004OEM

Brands by name

Popular brands