MTD 737-0168 Operator'S Manual Download

Page: 25 / 28

Styles C & D

REF.

NO.

PART

NO.

DESCRIPTION

731-2643

Clean Out Tool

684-04057

Impeller Assembly, 12” Diameter

710-0347

Hex Screw, 3/8-16, 1.75, Gr5, Std

710-0451

Bolt, Carriage, 5/16-18, .750 Gr1

710-0703

Screw, Carriage, 1/4-20, .75, Gr5

710-0726

Screw, Self-tapping, 5/16-12, 0.750

712-04063

Nut, Flange Lock, 5/16-18, Grf, Nylon

712-04064

Nut, Flange Lock, 1/4-20, Grf, Nylon

712-04065

Nut, Flange Lock, 3/8-16, Grf, Nylon

714-0149B

Internal Cotter Pin

725-0157

Cable, Tie, 3/16 x .05 x 7.4

726-04012

Nut, Push-on, .25 Diameter

731-04705

Chute, Adapter 5” Diameter

732-0611

Spring, Extension, .38 OD x 3.6

736-0174

Washer, Wave, .625 x.885 x.015

731-2635 Mount, Clean Out Tool

738-0143

Screw, Shoulder, .498 x .340, 3/8-16

738-0281

Screw, Shoulder, .625 x .170, 3/8-16

738-04124

Pin, Shear, .25 x 1.50, Gr2

741-0245

Bearing, Hex Flange x .75 ID

741-0309

Bearing, Ball, .75 ID x 1.85 OD

756-0981A

Idler Pulley, Flat 2.75 OD

790-00075

Housing, Bearing, 1.85 ID

790-00080

Bracket, Auger Idler w/ Brake

618-04170

Gearbox Assembly, Auger, 22”

618-04171

Gearbox Assembly, Auger, 24”

618-04172

Gearbox Assembly, Auger, 26”

618-04173

Gearbox Assembly, Auger, 28”

684-04067

Housing Assembly, Auger 22”

684-04069

Housing Assembly, Auger 24”

684-04071

Housing Assembly, Auger 26”

684-04073

Housing Assembly, Auger 28”

684-04107

Spiral Assembly, LH

684-04108

Spiral Assembly, RH

714-04040

Bow-Tie Cotter Pin

731-04870*

Spacer, 1.25 OD x .75 ID x 1.00

736-0188

Washer, Flat, .76 x 1.49 x .06

738-04124

Shear Pin, .25 x 1.50, Gr2

741-0493A

Bushing, Flange, .800 ID x .910 OD

790-00087

Housing, Bearing, 1” Hex

790-00117

Plate, Shave, 2.25 x 21.66

790-00120

Plate, Shave, 2.25 x 23.66

790-00121

Plate, Shave, 2.25 x 25.66

790-00118

Plate, Shave, 2.25 x 27.66

710-04071

Bolt, Carriage, 5/16-18, 1.0

720-04032

Knob Assembly

731-04426A

Chute, Upper, w/ Domestic Label

731-04869

Chute, Keeper Flange

731-04912

Chute, Lower, 5.0 Diameter

736-0159

Washer.349 ID x .879 OD x .063

741-0475

Bushing, Plastic, .380

784-5647

Bracket, Chute Crank

784-5580

Shoe, Slide

719-0319

Housing, Auger, RH Reduced

719-0320

Housing, Auger, LH Reduced

721-0179

Seal, Oil, .750 ID

741-0662

Bearing, Flange, .75 ID x 1.00 OD x .59

710-0642

Screw, Self-tapping, 1/4-20, 0.750

711-04286

Axle, Auger, 22"

711-04285

Axle, Auger, 24"

711-04284

Axle, Auger, 26"

711-04283

Axle, Auger, 28"

714-0161

Key, Hi-pro 3/16 x 5/8

715-04021

Pin, Dowel, .25 OD x 1.2

717-04126

Shaft, Worm .75 OD

717-0528A

Gear, Worm 20T

718-04071

Collar, Thrust

721-0325

Plug, 1/4 x .437

721-0327

Seal, Oil, .75 x 1 x .131

736-0351

Washer, Flat, .760 ID x 1.5 OD

736-3084

Washer, Flat, .51 x 1.12

741-0663

Bearing, Flange, .75 ID x 1.00 OD x .925

746-0897

Auger Clutch Cable, 44.75”

741-0661A

Bearing, Flange, .75 ID x 1.00 OD x .975

629-0071

Cord, Extension

710-0726

Bolt, Carriage, 5/16-18, 1.0 Gr1

REF.

NO.

PART

NO.

DESCRIPTION

* None found between spirals on models with 22-inch auger housing.

* One found between spirals on models with 24-inch auger housing.

* Two found between spirals on models with 26-inch auger housing.

* Three found between spirals on models with 28-inch auger housing.

NOTE:

Snow thrower features and components vary by model. NOT all parts listed above and pictured on the previous page
are standard equipment.

Summary of Contents for 737-0168





























Search results

Summary of Contents for 737-0168

Reviews:

Related manuals for 737-0168

Brands by name

Popular brands

MTD 737-0168, Operator'S Manual

Search results

Summary of Contents for 737-0168

Reviews:

Related manuals for 737-0168

Brands by name

Popular brands